| Electronic Components Datasheet Search |
|
EVAL-AD5449EBZ Datasheet(PDF) 14 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
EVAL-AD5449EBZ Datasheet(HTML) 14 Page - Analog Devices |
|
14 / 32 page ![]() AD5429/AD5439/AD5449 Rev. C | Page 14 of 32 TERMINOLOGY Relative Accuracy (Endpoint Nonlinearity) A measure of the maximum deviation from a straight line passing through the endpoints of the DAC transfer function. It is measured after adjusting for zero and full scale and is typically expressed in LSBs or as a percentage of the full-scale reading. Differential Nonlinearity The difference in the measured change and the ideal 1 LSB change between two adjacent codes. A specified differential nonlinearity of −1 LSB maximum over the operating temperature range ensures monotonicity. Gain Error (Full-Scale Error) A measure of the output error between an ideal DAC and the actual device output. For these DACs, ideal maximum output is VREF − 1 LSB. The gain error of the DACs is adjustable to zero with an external resistance. Output Leakage Current The current that flows into the DAC ladder switches when they are turned off. For the IOUT1x terminal, it can be measured by loading all 0s to the DAC and measuring the IOUT1 current. Minimum current flows into the IOUT2x line when the DAC is loaded with all 1s. Output Capacitance Capacitance from IOUT1 or IOUT2 to AGND. Output Current Settling Time The amount of time for the output to settle to a specified level for a full-scale input change. For these devices, it is specified with a 100 Ω resistor to ground. Digital-to-Analog Glitch Impulse The amount of charge injected from the digital inputs to the analog output when the inputs change state. This is normally specified as the area of the glitch in either pA-sec or nV-sec, depending on whether the glitch is measured as a current or voltage signal. Digital Feedthrough When the device is not selected, high frequency logic activity on the digital inputs of the device is capacitively coupled through the device and produces noise on the IOUT pins and, subsequently, on the circuitry that follows. This noise is digital feedthrough. Multiplying Feedthrough Error The error due to capacitive feedthrough from the DAC reference input to the DAC IOUT1x terminal when all 0s are loaded to the DAC. Digital Crosstalk The glitch impulse transferred to the outputs of one DAC in response to a full-scale code change (all 0s to all 1s, or vice versa) in the input register of the other DAC. It is expressed in nV-sec. Analog Crosstalk The glitch impulse transferred to the output of one DAC due to a change in the output of another DAC. It is measured by loading one of the input registers with a full-scale code change (all 0s to all 1s, or vice versa) while keeping LDAC high and then pulsing LDAC low and monitoring the output of the DAC whose digital code has not changed. The area of the glitch is expressed in nV-sec. Channel-to-Channel Isolation The portion of input signal from the reference input of a DAC that appears at the output of another DAC. It is expressed in dB. Total Harmonic Distortion (THD) The DAC is driven by an ac reference. The ratio of the rms sum of the harmonics of the DAC output to the fundamental value is the THD. Usually only the lower-order harmonics are included, such as the second to fifth harmonics. 1 5 4 3 2 V V V V V THD 2 2 2 2 log 20 + + + = Intermodulation Distortion (IMD) The DAC is driven by two combined sine wave references of Frequency fa and Frequency fb. Distortion products are produced at sum and difference frequencies of mfa ± nfb, where m, n = 0, 1, 2, 3 … Intermodulation terms are those for which m or n is not equal to 0. The second-order terms include (fa + fb) and (fa − fb), and the third-order terms are (2fa + fb), (2fa − fb), (f + 2fa + 2fb), and (fa − 2fb). IMD is defined as l Fundamenta the of Amplitude RMS Products Distortion Diff and Sum the of Sum RMS IMD log 20 = Compliance Voltage Range The maximum range of (output) terminal voltage for which the device provides the specified characteristics. |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |