| Electronic Components Datasheet Search |
|
OM6206U/Z Datasheet(PDF) 14 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
OM6206U/Z Datasheet(HTML) 14 Page - NXP Semiconductors |
|
14 / 36 page ![]() 2001 Nov 14 14 Philips Semiconductors Product specification 65 × 102 pixels matrix LCD driver OM6206 TC1 and TC0 00 VLCD temperature coefficient 0 00 01 VLCD temperature coefficient 1 10 VLCD temperature coefficient 2 11 VLCD temperature coefficient 3 S1 and S0 00 2 × voltage multiplier 00 01 3 × voltage multiplier 10 4 × voltage multiplier 11 5 × voltage multiplier BS2 to BS0 − bias system 000 VOP6 to VOP0 − VLCD programming 0000000 BIT BIT VALUE DESCRIPTION RESET STATE 8.1 Initialization Immediately following power-on, all internal registers as well as the RAM content are undefined. A RES pulse must be applied. Reset is accomplished by applying an external reset pulse (active LOW) at pin RES. When reset occurs within the specified time, all internal registers are reset however the RAM is still undefined. The state after reset is described in Section 8.2. RES input must be ≤0.3VDD when VDD reaches VDD(min) (or higher) within a maximal time tVHRL after VDD going HIGH (see Fig.16). 8.2 Reset function After reset the LCD driver has the following state: • Power-down mode (PD = 1) • Horizontal addressing (V = 0) • Normal instruction set (H = 0) • Display blank (E andD=0) • Address counter X6 to X0 = 0, Y3 to Y0 =0 • Temperature control (TC1 and TC0 =0) • Bias system (BS2 to BS0 =0) • VLCD is equal to 0 V and the high-voltage generator is switched off (VOP6 to VOP0 = 0 and PRS = 0) • After power-on, RAM data are undefined, the reset signal does not change the content of the RAM • All LCD outputs at VSS (display off). 8.3 Function set 8.3.1 PD When PD = 1 the chip is in Power-down mode: • All LCD outputs at VSS (display off) • Bias generator and VLCD generator off; VLCD can be disconnected • Oscillator off (external clock possible) • Serial bus: command, function etc. • RAM contents not cleared; RAM data can be written • VLCD discharged to VSS in Power-down mode. 8.3.2 V When V = 0, the horizontal addressing is selected. The data is written into the DDRAM as shown in Fig.6. When V = 1, the vertical addressing is selected. The data is written into the DDRAM as shown in Fig.5. 8.3.3 H When H = 0 the commands ‘display control’, ‘set Y-address’, ‘set X-address’ and ‘set the PRS bit’ (LOW or HIGH range of the high-voltage generator) can be performed; when H = 1 the others can be executed. The commands ‘write data’ and ‘function set’ can be executed in both cases. 8.4 Display control 8.4.1 D AND E The bits D and E select the display mode (see Table 2). |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |