R5F5671CDDLE datasheet(10/179 Pages) RENESAS

10 / 179 page

RX671 Group

1. Overview

R01DS0373EJ0120 Rev.1.20

Page 10 of 179

Sep 30, 2024

12-bit A/D converter (S12ADFa)

 12 bits × 2 units (unit 0: 8 channels; unit 1: 12 channels)

 12-bit resolution (switchable between 8, 10, and 12 bits)

 Conversion time

0.48 µs per channel (for 12-bit conversion)

0.45 µs per channel (for 10-bit conversion)

0.42 µs per channel (for 8-bit conversion)

 Operating mode

Scan mode (single scan mode, continuous scan mode, or 3 group scan mode)

Group priority control (only for 3 group scan mode)

 Sample-and-hold function

Common sample-and-hold circuit included

 Sampling variable

Sampling time can be set up for each channel.

 Digital comparison

Method: Comparison to detect voltages above or below thresholds and window

comparison

Measurement: Comparison of two results of conversion or comparison of a value in the

comparison register and a result of conversion

 Self-diagnostic function

The self-diagnostic function internally generates three analog input voltages

(unit 0: VREFL0, VREFH0 × 1/2, VREFH0; unit 1: AVSS1, AVCC1 × 1/2, AVCC1)

 Double trigger mode (A/D conversion data duplicated)

 Detection of analog input disconnection

 Three ways to start A/D conversion

Software trigger, timer (MTU, TMR, TPU) trigger, external trigger

 Event linking by the ELC

Temperature sensor

 1 channel

 Relative precision: ± 1°C

 The voltage of the temperature is converted into a digital value by the 12-bit A/D

converter (unit 1).

Capacitive touch sensing unit (CTSUa)

 Detection pin: 17 channels

Safety

Memory protection unit

(MPU)

 Protection area: Eight areas (max.) can be specified in the range from 0000 0000h to

FFFF FFFFh.

 Minimum protection unit: 16 bytes

 Reading from, writing to, and enabling the execution access can be specified for each

area.

 An access exception occurs when the detected access is not in the permitted area.

Trusted Memory (TM)

Function

 Programs in the TM target area in the code flash memory are protected against reading

 Instruction fetching by the CPU is the only form of access to these areas when the TM

function is enabled.

function

 Protects important registers from being overwritten for in case a program runs out of

control.

CRC calculator (CRCA)

 Generation of CRC codes for 8-/32-bit data

8-bit data

Selectable from the following three polynomials

X8 + X2 + X + 1, X16 + X15 + X2 + 1, X16 + X12 + X5 + 1

32-bit data

Selectable from the following two polynomials

X32 + X26 + X23 + X22 + X16+ X12 + X11 + X10 + X8+ X7 + X5 + X4 + X2+ X + 1,

X32 + X28 + X27 + X26 + X25 + X23 + X22 + X20 + X19 + X18 + X14 + X13 + X11 + X10 + X9 +

X8 + X6 + 1

 Generation of CRC codes for use with LSB-first or MSB-first communications is

selectable

Main clock oscillation

stop detection

 Main clock oscillation stop detection: Available

Clock frequency

accuracy measurement

circuit (CAC)

 Monitors the clock output from the main clock oscillator, sub-clock oscillator, low- and

high-speed on-chip oscillators, IWDT-dedicated on-chip oscillator, and PCLKB, and

generates interrupts when the setting range is exceeded.

Data operation circuit

(DOCA)

 This handles the comparison, addition, subtraction, comparison in terms of which is

larger or smaller, or window comparison of 32-bit values.

Table 1.1

Outline of Specifications (9/10)

Classification

Module/Function

Description

R5F5671CDDLE Datasheet(PDF) 10 Page - Renesas Technology Corp

R5F5671CDDLE Datasheet(HTML) 10 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL