UPSD3233 datasheet(120/170 Pages) STMICROELECTRONICS

120 / 170 page

uPSD3234A, uPSD3234BV, uPSD3233B, uPSD3233BV

120/170

The Port pin’s tri-state output driver enable is con-

trolled by a two input OR gate whose inputs come

from the CPLD AND Array enable product term

and the Direction Register. If the enable product

term of any of the Array outputs are not defined

and that port pin is not defined as a CPLD output

in the PSDsoft, then the Direction Register has

sole control of the buffer that drives the port pin.

The contents of these registers can be altered by

the MCU. The Port Data Buffer (PDB) feedback

path allows the MCU to check the contents of the

registers.

Ports A, B, and C have embedded Input Macro-

cells (IMC). The Input Macrocells (IMC) can be

configured as latches, registers, or direct inputs to

the PLDs. The latches and registers are clocked

by Address Strobe (ALE) or a product term from

the PLD AND Array. The outputs from the Input

Macrocells (IMC) drive the PLD input bus and can

read

the

MCU.

See

Input

Macrocell, page 118.

Port Operating Modes

The I/O Ports have several modes of operation.

Some modes can be defined using PSDsoft, some

by the MCU writing to the Control Registers in

CSIOP space, and some by both. The modes that

can only be defined using PSDsoft must be pro-

grammed into the device and cannot be changed

unless the device is reprogrammed. The modes

that can be changed by the MCU can be done so

dynamically at run-time. The PLD I/O, Data Port,

Address Input, and Peripheral I/O Modes are the

only modes that must be defined before program-

ming the device. All other modes can be changed

by the MCU at run-time. See Application Note

AN1171 for more detail.

Table 92., page 121 summarizes which modes

are available on each port. Table 95., page 122

shows how and where the different modes are

configured. Each of the port operating modes are

described in the following sections.

MCU I/O Mode

In the MCU I/O Mode, the MCU uses the I/O Ports

block to expand its own I/O ports. By setting up the

CSIOP space, the ports on the PSD Module are

mapped into the MCU address space. The ad-

dresses

the

ports

are

listed

Table

84., page 98.

A port pin can be put into MCU I/O Mode by writing

a '0' to the corresponding bit in the Control Regis-

ter. The MCU I/O direction may be changed by

writing to the corresponding bit in the Direction

See Peripheral I/O Mode, page 120. When the pin

is configured as an output, the content of the Data

Out Register drives the pin. When configured as

an input, the MCU can read the port input through

the Data In buffer. See Figure 63., page 119.

Ports C and D do not have Control Registers, and

are in MCU I/O Mode by default. They can be used

for PLD I/O if equations are written for them in PS-

Dabel.

PLD I/O Mode

The PLD I/O Mode uses a port as an input to the

CPLD’s Input Macrocells (IMC), and/or as an out-

put from the CPLD’s Output Macrocells (OMC).

The output can be tri-stated with a control signal.

This output enable control signal can be defined

by a product term from the PLD, or by resetting the

corresponding bit in the Direction Register to '0.'

The corresponding bit in the Direction Register

must not be set to '1' if the pin is defined for a PLD

input signal in PSDsoft. The PLD I/O Mode is

specified in PSDsoft by declaring the port pins,

and then writing an equation assigning the PLD I/

O to a port.

Address Out Mode

Address Out Mode can be used to drive latched

MCU addresses on to the port pins. These port

pins can, in turn, drive external devices. Either the

output enable or the corresponding bits of both the

Direction Register and Control Register must be

set to a '1' for pins to use Address Out Mode. This

must be done by the MCU at run-time. See Table

94., page 121 for the address output pin assign-

ments on Ports A and B for various MCUs.

Peripheral I/O Mode

Peripheral I/O Mode can be used to interface with

external peripherals. In this mode, all of Port A

serves as a tri-state, bi-directional data buffer for

the MCU. Peripheral I/O Mode is enabled by set-

ting Bit 7 of the VM Register to a '1.' Figure

64., page 121 shows how Port A acts as a bi-di-

rectional buffer for the MCU data bus if Peripheral

I/O Mode is enabled. An equation for PSEL0 and/

or PSEL1 must be written in PSDsoft. The buffer is

tri-stated when PSEL0 or PSEL1 is low (not ac-

tive). The PSEN signal should be “ANDed” in the

PSEL equations to disable the buffer when PSEL

resides in the data space.

JTAG In-System Programming (ISP)

Port C is JTAG compliant, and can be used for In-

System Programming (ISP). For more information

on the JTAG Port, see PROGRAMMING IN-CIR-

CUIT

USING

THE

JTAG

SERIAL

INTERFACE, page 134.

UPSD3233 Datasheet(PDF) 120 Page - STMicroelectronics

UPSD3233 Datasheet(HTML) 120 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL