Electronic Components Datasheet Search
  New Zealand  ▼
ALLDATASHEET.CO.NZ

X  

FHS40-P Datasheet(PDF) 7 Page - LEM

Part # FHS40-P
Description  Current transducer
PDF  18 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  LEM [LEM]
Direct Link  http://www.lem.co.jp/HQ/en
Logo LEM - LEM

FHS40-P Datasheet(HTML) 7 Page - LEM

Back Button FHS40-P Datasheet HTML 3Page - LEM FHS40-P Datasheet HTML 4Page - LEM FHS40-P Datasheet HTML 5Page - LEM FHS40-P Datasheet HTML 6Page - LEM FHS40-P Datasheet HTML 7Page - LEM FHS40-P Datasheet HTML 8Page - LEM FHS40-P Datasheet HTML 9Page - LEM FHS40-P Datasheet HTML 10Page - LEM FHS40-P Datasheet HTML 11Page - LEM Next Button
Zoom Inzoom in Zoom Outzoom out
 7 / 18 page
background image
Page 7/18
LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice.
www.lem.com
100727/10
FHS 40-P/SP600
0 - 100A
Typical connection diagram and ground plane
Values of the electrical data given page 3 are according to the following connection diagram.
Figure 6: Typical connection diagram (C
1 = C3 = 47 nF, C2 = 4.7 nF)
Careful design of the PCB is needed to ensure minimum disturbance by surrounding currents and external fields.
C
1 to C3 should be mounted as close as possible to the pins.
The maximum capacitor value allowed on
V
OUT is 18 nF. It is recommended to use 4.7 nF.
The maximum capacitor value allowed on
V
OUTFast is 330 pF.
A positive output voltage V
S is obtained with a current (IP) flowing under Minisens from the pin 4/5 end of the package to the pin
1/8 end.
V
SFast is negative when VS is positive.
If the pin
V
OUTFast is not used, it should be connected only to a small solder pad. Coupling to other tracks should be minimized.
An internally generated reference voltage of 2.5 V with a source resistance of 200 Ω is available on the pin
V
REF. The voltage
on this pin may be forced externally with a voltage in the range 1.5 - 2.8 V. The output voltage
V
S is limited to approximately the
value of
V
REF in both positive and negative polarities.
V
STANDBY should be connected to a low impedance so that capacitive coupling from adjacent tracks does not disturb it (there is an
internal pull-down whose resistance is 500 kΩ). It should be connected to 0 V if not used.
Connect
V
STANDBY to the same voltage as VC to activate the Standby mode. VREF should not be forced in Standby mode.
Minisens can be directly mounted above the PCB track in which the current to be measured flows (see kit 4, for example).
+5V
VSTANDBY
Primary
conductor
IP
C3
VC
VOUT
0 V
isolation
barrier
•
STANDBY
VREF
VS
1
VOUTFast
0 V
C1
C2
VSFast
8
2
3
4
5, 6
7
•
•



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com