TMS320DM814X datasheet(271/376 Pages) TI1

271 / 376 page

TMS320DM8148, TMS320DM8147

www.ti.com

SPRS647E – MARCH 2011 – REVISED DECEMBER 2013

8.9

High-Definition Multimedia Interface (HDMI)

The device includes an HDMI 1.3a-compliant transmitter for digital video and audio data to display

devices. The HDMI interface consists of a digital HDMI transmitter core with TMDS encoder, a core

wrapper with interface logic and control registers, and a transmit PHY, with the following features:

•

Hot-plug detection

•

Consumer electronics control (CEC) messages

•

DVI 1.0 compliant (only RGB pixel format)

•

CEA 861-D and VESA DMT formats

•

Supports up to 165-MHz pixel clock

–

1920 x 1080p @75 Hz with 8-bit/component color depth

–

1600 x 1200 @60 Hz with 8-bit/component color depth

•

Support for deep-color mode:

–

10-bit/component color depth up to 1080p @60 Hz (Max pixel clock = 148.5 MHz)

–

12-bit/component color depth up to 720p/1080i @60 Hz (Max pixel clock = 123.75 MHz)

•

TMDS clock to the HDMI-PHY is up to 185.625 MHz

•

Maximum supported pixel clock:

–

165 MHz for 8-bit color depth

–

148.5 MHz for 10-bit color depth

–

123.75 MHz for 12-bit color depth

•

Uncompressed multichannel (up to eight channels) audio (L-PCM) support

•

Master I2C interface for display data channel (DDC) connection

For more details on the HDMI, see the High-Definition Multimedia Interface (HDMI) chapter of the

TMS320DM814x DaVinci Digital Media Processors Technical Reference Manual (Literature Number:

SPRUGZ8).

8.9.1

HDMI Design Guidelines

This section provides PCB design and layout guidelines for the HDMI interface. The design rules constrain

PCB trace length, PCB trace skew, signal integrity, cross-talk, and signal timing. Simulation and system

design work has been done to ensure the HDMI interface requirements are met.

8.9.1.1

HDMI Interface Schematic

The HDMI bus is separated into three main sections:

1. Transition Minimized Differential Signaling (TMDS) high-speed digital video interface

2. Display Data Channel (I2C bus for configuration and status exchange between two devices)

3. Consumer Electronics Control (optional) for remote control of connected devices.

The DDC and CEC are low-speed interfaces, so nothing special is required for PCB layout of these

signals. Their connection is shown in Figure 8-37, HDMI Interface High-Level Schematic.

The TMDS channels are high-speed differential pairs and, therefore, require the most care in layout.

Specifications for TMDS layout are below.

Figure 8-37 shows the HDMI interface schematic. The specific pin numbers can be obtained from Table 3-

15, HDMI Terminal Functions.

Peripheral Information and Timings

271

Submit Documentation Feedback

Product Folder Links: TMS320DM8148 TMS320DM8147

TMS320DM814x Datasheet(PDF) 271 Page - Texas Instruments

TMS320DM814x Datasheet(HTML) 271 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL