PIC12CE673-04SLASHP datasheet(40/116 Pages) MICROCHIP

40 / 116 page

PIC12CE67X

DS40181B-page 40

Preliminary

8.1

A/D Sampling Requirements

For the A/D converter to meet its speciﬁed accuracy,

the charge holding capacitor (CHOLD) must be allowed

to fully charge to the input channel voltage level. The

analog input model is shown in Figure 8-4. The source

impedance (RS) and the internal sampling switch (RSS)

impedance directly affect the time required to charge

the capacitor CHOLD. The sampling switch (RSS)

impedance varies over the device voltage (VDD), see

Figure 8-4.

The maximum recommended imped-

ance for analog sources is 10 k

Ω. After the analog

input channel is selected (changed) this acquisition

must be done before the conversion can be started.

To calculate the minimum acquisition time, Equation 8-

1 may be used. This equation assumes that 1/2 LSb

error is used (512 steps for the A/D). The 1/2 LSb error

is the maximum error allowed for the A/D to meet its

speciﬁed resolution.

EQUATION 8-1:

A/D MINIMUM CHARGING

TIME

VHOLD = (VREF - (VREF/512)) • (1 - e(-Tc/C

HOLD

(RIC + RSS + RS)))

Tc = -(51.2 pF)(1 k

Ω + RSS + RS) ln(1/511)

Example 8-1 shows the calculation of the minimum

required acquisition time TACQ. This calculation is

based on the following system assumptions.

Rs = 10 k

Ω

1/2 LSb error

VDD = 5V

→ Rss = 7 kΩ

Temp (system max.) = 50

°C

VHOLD = 0 @ t = 0

EXAMPLE 8-1:

CALCULATING THE

MINIMUM REQUIRED

SAMPLE TIME

TACQ = Ampliﬁer Settling Time +

Holding Capacitor Charging Time +

Temperature Coefﬁcient

TACQ = 5

µs + Tc + [(Temp - 25°C)(0.05 µs/°C)]

TC =

-CHOLD (RIC + RSS + RS) ln(1/512)

-51.2 pF (1 k

Ω + 7 kΩ + 10 kΩ) ln(0.0020)

-51.2 pF (18 k

Ω) ln(0.0020)

-0.921

µs (-6.2146)

5.724

µs

TACQ = 5

µs + 5.724 µs + [(50°C - 25°C)(0.05 µs/°C)]

10.724

µs + 1.25 µs

11.974

µs

Note 1: The reference voltage (VREF) has no

effect on the equation, since it cancels

itself out.

Note 2: The charge holding capacitor (CHOLD) is

not discharged after each conversion.

Note 3: The maximum recommended impedance

for analog sources is 10 k

Ω. This is

required to meet the pin leakage speciﬁ-

cation.

Note 4: After a conversion has completed, a

2.0 TAD delay must complete before

acquisition can begin again. During this

time the holding capacitor is not con-

nected to the selected A/D input channel.

FIGURE 8-4:

ANALOG INPUT MODEL

CPIN

RAx

5 pF

VDD

VT = 0.6V

I leakage

RIC

≤ 1k

Sampling

Switch

RSS

CHOLD

= DAC capacitance

VSS

Sampling Switch

5 6 7 8 9 10 11

( k

Ω )

VDD

= 51.2 pF

± 500 nA

Legend CPIN

I leakage

RIC

CHOLD

= input capacitance

= threshold voltage

= leakage current at the pin due to

= interconnect resistance

= sampling switch

= sample/hold capacitance (from DAC)

various junctions

PIC12CE673-04/P Datasheet(PDF) 40 Page - Microchip Technology

PIC12CE673-04/P Datasheet(HTML) 40 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL