C-108

Multifunction Preset Counter

H7CX (Counter Function)

Settings for All Functions

Note: At the time of delivery, the H7CX is set to the 1-stage counter (2-stage counter for H7CX-AW

@/-A4W@ models) configuration. When using

as a 2-stage (or 1-stage) counter, total and preset counter, batch counter, or dual counter, switch to the configuration using the procedure

given on page 124.

(1ms)

(20ms)

(30Hz)

(5kHz)

(N)

(0.50s) (99.99s)

(0.01s)

(0.50s) (99.99s)

(0.01s)

(0.01s) (99.99s)

(F)

(C)

(R)

(K-1)

(P)

(Q)

(A)

(K-2)

(D)

(L)

(H)

(KP-1)

(KP-2)

(KP-3)

(KP-4)

(KP-5)

(99.999)

[9.999]

(1.000)

(0.001)

(0.50s)

(99.99s)

(0.01s)

∼

∼

The characters displayed in reverse video are the default settings.

Power ON

Note 4: Displayed for output modes other than K-2, D, L, and H only.

Input mode

Output mode

Display color

See note 1.

See note 2.

For details on operations in run mode, refer to page 25.

3 s min.

3 s min.

When using as a 2-stage counter:

(Addition) (Subtraction)

(Outputs held)

See note 7.

See note 3.

See note 6.

See note 5.

See note 4.

See note.

See note 4.

See note 5.

See note 5.

See note 5.

Note: Displayed for terminal-block models (except H7CX-A11

@) only.

(Red)

(Green)

(Red-green) (Green-red)

Settings that cannot be performed with the DIP switch are performed with the operation keys.

When using as a dual counter:

Note 3:

Note 6:

See note 7.

Note: Displayed for H7CX-AU

@ models only.

Note: 1. If the mode is switched to the function setting mode during operation, operation will con-

tinue.

2. Changes made to settings in function setting mode are enabled for the first time when the

mode is changed to run mode. Also, when settings are changed, the counter is reset

(present value initialized and output turned OFF) on returning to run mode.

When performing settings with operation keys only, set pin1 of the DIP switch to OFF (factory setting).

If pin 1 of the DIP switch is set to ON, the setting items indicated by

will not be displayed.

Key protect

level

Output

allocation

NPN/PNP

input mode

Prescale

value

Decimal

point

position

Reset input

signal

width

Counting

speed

One-shot

output

time

(UP)

(DOWN) (UP/DOWN A) (UP/DOWN B) (UP/DOWN C)

Dual count

calculating mode

Note: Displayed for output modes

other than K-2, D, L, and H

only.

Note: 5. Display only when the input mode is UP/DOWN A, B,

or C with 6-digit models (with H7CX-AU

@/-AW@

models only for H).

One-

shot

output

2 time

One-

shot

output

1 time

One-

shot

output

2 time

Note: Displayed only when the output mode is C, R, K-1, P,

Q, A, or K-2.

Note: Displayed only when the

output mode is C, R, K-1,

P, Q, A, or K-2.

If the output time is 0.00, hold is

displayed.

Note 1: Displayed for output modes

other than D, L, and H.

Note 2: HOLD cannot be set when the

output mode is K-2.

Note: Displayed only when the output

mode is C, R, K-1, P, Q, A, or K-2.

When using as a

batch counter:

No decimal

point

One digit after

decimal point

Two digits after

decimal point

Three digits after

decimal point

Note 7: The displays for 4-digit models are shown inside

parentheses.

(NPN

input)

(PNP

input)

Set each setting item using the

keys. (

key only for 6-digit models)

r