| Electronic Components Datasheet Search |
|
HT45R37V Datasheet(PDF) 23 Page - Holtek Semiconductor Inc |
|
|
|||||||||||||||||||||||||||||
HT45R37V Datasheet(HTML) 23 Page - Holtek Semiconductor Inc |
|
23 / 90 page ![]() HT45R37V Rev. 1.00 23 October 20, 2009 VFD Driver The device includes a VFD driver function to drive VFD panel high voltage filaments and buzzer. The microcontroller communicates serially with the VFD driver transmitting the display data into a 24-bit shift reg- ister within the driver. This VFD driver converts the shift register into VFD panel driving signals and makes the necessary voltage level shifting. The microcontroller will only transmit data to the VFD driver, no data is transmit- ted from the VFD driver to the microcontroller. VFD Interface A five line interface exists between the microcontroller and the VFD driver as shown in the diagram. Data transmission between the microcontroller and the VFD interface is conducted via a three line interface us- ing the CLK, DATA and STROBE lines. As data commu- nication is only one way the microcontroller I/O pins must bet setup as outputs. The buzzer control input BZI will be transformed into a complementary pair of outputs BZO and BZO by a con- verter in the VFD driver. These complementary buzzer outputs will also be level shifted to a higher voltage by the converter. The VFD driver filament control input, F1, will also be shifted to a high voltage output called F1O, that can be used to switch the filaments on and off. 24-bit Shift Register/Latch Data transmitted from the microcontroller is transmitted serially and will be first written into a 24-bit shift register located within the VFD driver. These 24-bits are used to control the VFD panel segments, VFD0~VFD15, and grid, VFD16~VFD23, lines. The control method is as fol- lows: · Use the ²DATA² and ²CLK² lines to shift data into the internal 24-bit shift register. Data is clocked into the shift-register on the positive clock edge. This data cor- responds to the desired VFD0~VFD23 output display data. The VFD outputs will only change if the STROBE line is high. If the STROBE line is low, only the shift register data will be modified and the VFD outputs will remain the same. · Use the ²STROBE² line to latch the shift-register data to the VFD0~VFD23 outputs. When the STROBE line is high, the shift register data will be latched to the VFD lines. Note that the STROBE line is level and not edge triggered. S h i f t R e g i s t e r & L a t c h C o m p l e m e n t O u t p u t C o n v e r t e r L e v e l S h i f t e r V F D 0 V F D 2 3 F 1 O P a d N a m e V F D D r i v e r P B 3 P B 4 P B 5 I / O P B 2 S T R O B E C L K D A T A B Z I F 1 B Z O B Z O O u t p u t s VFD Driver C L K D A T A S T R O B E V F D 0 VFD Display Control Timing Diagram |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |