MEC1322 datasheet(53/456 Pages) MICROCHIP

53 / 456 page

 2014 - 2015 Microchip Technology Inc.

DS00001719D-page 53

MEC1322

Note 3-8

If the LRESET# pin is assigned to the GPIO function rather than LRESET#, the internal LRESET#

signal is gated low, and therefore the nRESET_OUT function will not operate properly.

3.6.1

INTEGRATED VCC1 POWER ON RESET (VCC1_RST#)

The VCC1_RST# pin is used to control the power up sequence for external devices. The VCC1_RST# timing is shown

in Section 38.1.1, "VCC1_RST# Timing," on page 397.

The following summarizes the operation of the VCC1_RST# signal.

• The VCC1_RST# pin is both a reset input and an output to the system.

• The VCC1_RST# output provides a POR reset during power up transition

• The VCC1_RST# output has Output Pin Glitch Protection

• The VCC1_RST# output stretches an external driven reset by 1ms (typ).

• The VCC1_RST# input detects an externally driven reset and places the MEC1322 into a VCC1 POR state.

The VCC1_RST# is an open drain pin. An external pull-up is required for the VCC1_RST# signal to be high.

The following sequence illustrates the interaction between the internally and externally driven assertion of VCC1_RST#:

The Integrated VCC1 Power On Reset Generator insures VCC1_RST# is driven low during a VCC1 POR from

VCC1 = 1V to 2.4V (typ) without glitches.

The VCC1_RST# pin is driven low during the POR transition until VCC1 > 2.4V (typ) and then the VCC1_RST#

pin remains low afterwards for 1ms (typ) delay window. The VCC1_RST# input is not examined during the 1ms

(typ) delay window; therefore, the system input and/or the external pin termination may be modified (i.e. drive it

low, let it float, etc.)

- The VCC1_RST# input is not examined during the POR transition while VCC1 < 2.4V (typ); therefore, the

system input to the VCC1_RST# pin may modify the output termination (i.e. drive it low, let it float, etc.)

The VCC1_RST# pin is driven low during the 1ms (typ) delay window. The MEC1322 is in the VCC1_POR state

during this time.

After the 1ms (typ) window, the VCC1_RST# pin open drain output from the MEC1322 is not driven/released.

The strap option pins are sampled at this time.

The MEC1322 will remain in the VCC1 POR for 2.65us (min) after the VCC1_RST# pin is released The

VCC1_RST# input pin is ignored during this time.

The VCC1_RST# pin input is sampled at 2.65us (min) after the VCC1_RST# pin is released.

- If the VCC1_RST# pin is high when sampled, then the EC starts executing.

- If the VCC1_RST# pin is low when sampled, the pin is being driven externally (i.e., the system is forcing a

reset):

- The VCC1_RST# pin is driven low for 1ms (typ), then sampled at 2.65us (min) after the VCC1_RST# pin is

released (see step 3).

WDT_RESET

Internal WDT Reset signal. This signal resets

VCC1 powered registers with the exception of

the WDT Event Count register. Note that the

glitch protect circuits do not activate on a WDT

reset. WDT_RESETdoes not reset VBAT

registers or logic.

A WDT_RESET is asserted by a WDT Event.

Note:

This event is indicated by the WDT

bit in the Power-Fail and Reset Sta-

tus Register

EC_PROC_

RESET

Internal reset signal to reset the processor in the

EC Subsystem.

An EC_PROC_ RESET is a stretched version of

the VCC1_RESET. This reset asserts at the

same time that VCC1_RESET asserts and is

held asserted for 1ms after the VCC1_RESET

deasserts.

Note:

The external pull-up on the VCC1_RST# pin must be chosen to meet the timing in Table 38-2,

“VCC1_RST# Rise Time,” on page 397.

TABLE 3-7:

DEFINITION OF RESET SIGNALS (CONTINUED)

Reset

Description

Source

MEC1322 Datasheet(PDF) 53 Page - Microchip Technology

MEC1322 Datasheet(HTML) 53 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL