TMS320DM814X datasheet(189/376 Pages) TI1

189 / 376 page

TMS320DM8148, TMS320DM8147

www.ti.com

SPRS647E – MARCH 2011 – REVISED DECEMBER 2013

7.3

Reset

7.3.1

System-Level Reset Sources

The device has several types of system-level resets. Table 7-8 lists these reset types, along with the reset

initiator, and the effects of each reset on the device.

Table 7-8. System-Level Reset Types

RESETS ALL

MODULES,

EXCLUDING EMAC

ASSERTS

RESETS EMAC

RESETS

PLL AND CLOCK

LATCHES

TYPE

INITIATOR

SWITCH,

RSTOUT_WD_OUT

SWITCH

EMULATION

CONFIG

BOOT PINS

EMULATION, PLL

AND CLOCK

CONFIG

Power-on Reset (POR)

POR pin

Yes

Optional

(1) (2)

External Warm Reset

RESET pin

Yes

Optional

(3)

Yes

Optional

(1) (2)

On-Chip Emulation

Emulation Warm Reset

Yes

Optional

(3)

Optional

(1)

Logic

Watchdog Reset

Watchdog Timer

Yes

Optional

(3)

Yes

Software Global Cold Reset

Software

Yes

Optional

(3)

Yes

Optional

(1)

Software Global Warm Reset

Software

Yes

Optional

(3)

Optional

(1)

Test Reset

TRST pin

Yes

(1)

RSTOUT_WD_OUT pin asserted only if BTMODE[11] was latched as "0" when coming out of reset.

(2)

While POR and/or RESET is asserted, the RSTOUT_WD_OUT pin is 3-stated and the internal pull resistor is disabled; therefore, an

external pullup/pulldown can be used to set the state of this pin (high/low) while POR and/or RESET is asserted. For more detailed

information on external PUs/PDs, see Section 4.5.1, Pullup/Pulldown Resistors.

(3)

EMAC Switch is NOT reset when the ISO_CONTROL bit in the RESET_ISO Control Module register is set to "1".

7.3.2

Power-on Reset (POR pin)

Power-on Reset (POR) is initiated by the POR pin and is used to reset the entire chip, including the Test

and Emulation logic, and the EMAC Switch. POR is also referred to as a cold reset since it is required to

be asserted when the device goes through a power-up cycle. However, a device power-up cycle is not

required to initiate a Power-on Reset.

The following sequence must be followed during a Power-on Reset:

1. Wait for the power supplies to reach normal operating conditions while keeping the POR pin asserted.

2. Wait for the input clock sources DEV_CLKIN, AUX_CLKIN, and SERDES_CLKN/P to be stable (if

used by the system) while keeping the POR pin asserted (low).

3. Once the power supplies and the input clock sources are stable, the POR pin must remain asserted

(low) [see Section 7.3.18, Reset Electrical Data/Timing]. Within the low period of the POR pin, the

following happens:

(a) All pins except Emulation pins enter a Hi-Z mode and the associated pulls, if applicable, will be

enabled.

(b) The PRCM asserts reset to all modules within the device.

4. The POR pin may now be de-asserted (driven high). When the POR pin is de-asserted (high):

(a) The BTMODE[15:0] pins are latched.

(b) Reset to the ARM Cortex-A8 and Modules without a local processor is de-asserted.

(d) The clock, reset, and power-down state of each peripheral is determined by the default settings of

the PRCM.

(e) The ARM Cortex-A8 begins executing from the Boot ROM.

Power, Reset, Clocking, and Interrupts

189

Submit Documentation Feedback

Product Folder Links: TMS320DM8148 TMS320DM8147

TMS320DM814x Datasheet(PDF) 189 Page - Texas Instruments

TMS320DM814x Datasheet(HTML) 189 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL