Electronic Components Datasheet Search
  New Zealand  ▼
ALLDATASHEET.CO.NZ

X  

AMIS41683CANN1RG Datasheet(PDF) 7 Page - ON Semiconductor

Part # AMIS41683CANN1RG
Description  Fault Tolerant CAN Transceiver
PDF  16 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  ONSEMI [ON Semiconductor]
Direct Link  http://www.onsemi.com
Logo ONSEMI - ON Semiconductor

AMIS41683CANN1RG Datasheet(HTML) 7 Page - ON Semiconductor

Back Button AMIS41683CANN1RG Datasheet HTML 3Page - ON Semiconductor AMIS41683CANN1RG Datasheet HTML 4Page - ON Semiconductor AMIS41683CANN1RG Datasheet HTML 5Page - ON Semiconductor AMIS41683CANN1RG Datasheet HTML 6Page - ON Semiconductor AMIS41683CANN1RG Datasheet HTML 7Page - ON Semiconductor AMIS41683CANN1RG Datasheet HTML 8Page - ON Semiconductor AMIS41683CANN1RG Datasheet HTML 9Page - ON Semiconductor AMIS41683CANN1RG Datasheet HTML 10Page - ON Semiconductor AMIS41683CANN1RG Datasheet HTML 11Page - ON Semiconductor Next Button
Zoom Inzoom in Zoom Outzoom out
 7 / 16 page
background image
AMIS−41682, AMIS−41683
http://onsemi.com
7
• Local Wake−up: Rising or falling edge on input WAKE
(levels maintained for a certain period).
• Remote Wake−up from CAN Bus: A message with five
consecutive dominant bits.
On a wake−up request the transceiver will set the output
on Pin INH high which can be used to activate the external
supply voltage regulator. Note: Pin INH is also set similarly
as an after wake up event by VBAT voltage being below the
battery power on flag level. (See FLAG_VBAT in Figure 5)
If VCC is provided, the wake−up request can be read on the
ERR or RXD outputs so the external microcontroller can
wake−up the transceiver (switch to normal operating mode)
via Pins STB and EN.
In the low power modes the failure detection circuit
remains partly active to prevent increased power
consumption in the event of failures 3, 3a, 4, and 7.
The go−to−sleep−mode is only a transition mode. The Pin
INH stays active for a limited time. During this time the
circuit can still go to another low−power mode. After this
time the circuit goes to the sleep−mode. In case of a wake up
request (from BUS or WAKE Pin) during this transition
time, the wake−up request has higher priority than
go−to−sleepand INH will not be deactivated.
Behavior in Case of Missing Supplies
If VCC is below the threshold level FLAG_VCC, the signals
on pins STB and EN will internally be set to low-level to
provide fail safe functionality. In this way, a low-power mode
will be forced in case of missing/failing VCC supply.
Similarly, missing/failing VBAT supply – i.e. VBAT being
below FLAG_VBAT level - will lead to a fail-safe behavior of
the transceiver by forcing a low-power mode.
A forced low-power in case of missing supplies
guarantees that the transceiver will in no way disturb the
other CAN nodes when the local electronic unit looses
ground or battery connection.
STB change state
Power−On Stand−by
High Low Act
EN change state
STB change state
1) Only when Vcc > POR_Vcc
2) INH active for a time = T_GoToSleep
3) Local Wake−upthrough pin Wake which change state
for a time > T_wake_min
Remote Wake−up through pin CANL or CANH when
dominant for a time >TCANH_min or TCANL_min
4) Mode Change through pins STB and EN is only
possible if Vcc > POR_Vcc
STB
ERR
RxD
INH
EN
RTL
POR−
flag
WU−
int
Vbat
Normal Mode
High High Act
STB
ERR
RxD
INH
EN
RTL
Err−
flag
Rec.
out
Vcc
Standby Mode
Low Low Act
STB
ERR
RxD
INH
EN
RTL
Vbat
GoTo Sleep Mode
Low High Act
2)
STB
ERR
RxD
INH
EN
RTL
Vbat
Sleep Mode
Low Low
Hz
STB
ERR
RxD
INH
EN
RTL
Vbat
WU−
int
WU−
int
WU−
int
WU−
int
WU−
int 1)
WU−
int 1)
EN change state
EN, STB change state
EN, STB change state
Time−out GoToSleep mode
Local or Remote
Wake−up 3)
Power−On
Mode Change 4)
Figure 5. Low Power Modes
Power−On
After power−on (VBAT switched on) the signal on Pin INH
will become high and an internal power−on flag will be set.
This flag can be read in the power−on standby mode via pin
ERR (STB = 1; EN = 0) and will be reset by entering the
normal operating mode.
Protections
A current limiting circuit protects the transmitter output
stages against short circuit to positive and negative battery
voltage. If the junction temperature exceeds a maximum
value, the transmitter output stages are disabled and flagged
on the ERR pin. Because the transmitter is responsible for
the major part of the power dissipation, this will result in
reduced power dissipation and hence a lower chip
temperature. All other parts of the IC will remain operating.
The Pins CANH and CANL are protected against
electrical transients that may occur in an automotive
environment.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com