| Electronic Components Datasheet Search |
|
PIC18F1220E/SOSQTP Datasheet(PDF) 182 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
PIC18F1220E/SOSQTP Datasheet(HTML) 182 Page - Microchip Technology |
|
182 / 308 page ![]() PIC18F1220/1320 DS39605F-page 180 © 2007 Microchip Technology Inc. 19.2 Watchdog Timer (WDT) For PIC18F1220/1320 devices, the WDT is driven by the INTRC source. When the WDT is enabled, the clock source is also enabled. The nominal WDT period is 4 ms and has the same stability as the INTRC oscillator. The 4 ms period of the WDT is multiplied by a 16-bit postscaler. Any output of the WDT postscaler is selected by a multiplexer, controlled by bits in Configuration Register 2H. Available periods range from 4 ms to 131.072 seconds (2.18 minutes). The WDT and postscaler are cleared when any of the following events occur: execute a SLEEP or CLRWDT instruction, the IRCF bits (OSCCON<6:4>) are changed or a clock failure has occurred. Adjustments to the internal oscillator clock period using the OSCTUNE register also affect the period of the WDT by the same factor. For example, if the INTRC period is increased by 3%, then the WDT period is increased by 3%. 19.2.1 CONTROL REGISTER Register 19-14 shows the WDTCON register. This is a readable and writable register, which contains a control bit that allows software to override the WDT enable configuration bit, only if the configuration bit has disabled the WDT. FIGURE 19-1: WDT BLOCK DIAGRAM REGISTER 19-14: WDTCON REGISTER Note 1: The CLRWDT and SLEEP instructions clear the WDT and postscaler counts when executed. 2: Changing the setting of the IRCF bits (OSCCON<6:4>) clears the WDT and postscaler counts. 3: When a CLRWDT instruction is executed the postscaler count will be cleared. U-0 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 — — — — — — —SWDTEN bit 7 bit 0 bit 7-1 Unimplemented: Read as ‘0’ bit 0 SWDTEN: Software Controlled Watchdog Timer Enable bit 1 = Watchdog Timer is on 0 = Watchdog Timer is off Note: This bit has no effect if the configuration bit, WDTEN (CONFIG2H<0>), is enabled. Legend: R = Readable bit W = Writable bit -n = Value at POR U = Unimplemented bit, read as ‘0’ INTRC Oscillator WDT Wake-up Reset WDT WDT Counter (31 kHz) Programmable Postscaler 1:1 to 1:32,768 Enable WDT WDTPS<3:0> SWDTEN WDTEN CLRWDT 4 from Sleep Reset All Device Sleep INTRC Control Resets ÷125 |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |