SCANSTA111MTSLASHNOPB datasheet(10/38 Pages) TI1

10 / 38 page

SCANSTA111

SNLS060K – AUGUST 2001 – REVISED APRIL 2013

www.ti.com

LEVEL 1 PROTOCOL (ADDRESSING MODES)

Table 3. SCANSTA111 Address Modes

Address Type

Hex Address

Binary Address

TDOB State

Direct Address

00 to 39,

00000000 to 00111010

Normal IEEE Std. 1149.1

40 to 7F.

01000000 to 01111111

(80 to FF(1))

(10000000 to 11111111(1))

Interrogation Address

00111010

Force strong 0' or weak 1' as ones-complement

address is shifted out.

Broadcast Address

00111011

Always TRI-STATED

Multi-Cast Group 0

00111100

Always TRI-STATED

Multi-Cast Group 1

00111101

Always TRI-STATED

Multi-Cast Group 2

00111110

Always TRI-STATED

Multi-Cast Group 3

00111111

Always TRI-STATED

(1)

Hex addresses 80' to FF' are only available when using the eighth address bit in the HDL version of the SCANSTA111. The Silicon part

has seven address lines and will treat the most-significant address bit as a don't care.

The SCANSTA111 supports single and multiple modes of addressing a 'STA111. The single mode selects one

'STA111 and is called Direct Addressing. More than one 'STA111 device can be selected via the Broadcast and

Multi-Cast Addressing modes.

DIRECT ADDRESSING: The 'STA111 enters the Wait-For-Address state when:

1. its TAP Controller enters the Test-Logic-Reset state, or

2. its instruction register is updated with the GOTOWAIT instruction (while either selected or unselected).

Each 'STA111 within a scan network must be statically configured with a unique address via its S(0-6) inputs.

While the 'STA111 controller is in the Wait-For-Address state, data shifted into bits 6 through 0 of the instruction

the instruction register match the address on the S(0-6) inputs, (see Figure 6) the 'STA111 becomes selected, and

is ready to receive Level 2 Protocol (i.e., further instructions). When the 'STA111 is selected, its device

identification register is inserted into the active scan chain.

All 'STA111s whose S(0-6) address does not match the instruction register address become unselected. An

unselected 'STA111 will remain unselected until either its TAP Controller enters the Test-Logic-Reset state, or its

instruction register is updated with the GOTOWAIT instruction.

BROADCAST ADDRESSING:

The Broadcast Address allows a tester to simultaneously select all 'STA111s in a test network. This mode is

useful in testing systems which contain multiple identical boards. To avoid bus contention between scan-path

output drivers on different boards, each 'STA111's TDOB buffer is always TRI-STATEd while in Broadcast mode.

In this configuration, the on-chip Linear Feedback Shift Register (LFSR) can be used to accumulate a test result

signature for each board that can be read back later by direct-addressing each board's 'STA111.

MULTICAST ADDRESSING:

As a way to make the broadcast mechanism more selective, the 'STA111 provides a Multi-cast addressing mode.

A 'STA111's multi-cast group register (MCGR) can be programmed to assign that 'STA111 to one of four (4)

Multi-Cast groups. When 'STA111s in the Wait-For-Address state are updated with a Multi-Cast address, all

'STA111s whose MCGR matches the Multi-Cast group will become selected. As in Broadcast mode, TDOB is

always TRI-STATEd while in Multi-cast mode.

Submit Documentation Feedback

Product Folder Links: SCANSTA111

SCANSTA111MT/NOPB Datasheet(PDF) 10 Page - Texas Instruments

SCANSTA111MT/NOPB Datasheet(HTML) 10 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38

Datasheet Download

Link URL