L9779WD-SPI datasheet(106/141 Pages) STMICROELECTRONICS

106 / 141 page

Functional description

L9779WD-SPI

106/141

DocID027721 Rev 2

Reset behaviour

All monitoring module registers are reset by RST_UV The following monitoring module

components are also reset by RST_PRL:

Note:

The signal RST_PRL (partial reset) is active when RST or SW_RST (Softreset) is active.

Access during a sequencer-run

A sequencer-run (which means the same as a monitoring cycle) is initiated by the writing of

a response (i.e. all answer bytes <RESP_BYTE3..0>) or a write to <RESPTIME> or by

reaching "end of time window". It must not be interrupted by a new access, i.e. the

monitoring module completes the action already started:



A sequencer-run was initiated by a "response write": The sequencer completes its task

with the data of the previous access and the new data are ignored.



A sequencer-run was initiated by a "response-time write": The sequencer uses the

response-time of the previous access, the error counter is correspondingly

incremented by one and the <CHRT> bit (REQUHI register) is set and the new data are

ignored. <CHRT> will be reset by reading and by the next start of a sequencer run (not

reset by the sequencer run that is started by a "response-time write"!)



A sequencer-run was initiated by "end of time window": The sequencer finishes the

started run, the error counter is incremented by one and the new data are ignored.

The writing of a response-time during a sequencer-run must not set the <CHRT> bit

(REQUHI register). The new response-time value is also not accepted. The writing of a

response during a sequencer-run must not set the <W_RESP> bit, the new response is also

not accepted.

Clock and time references

The monitoring module must work independently of the micro-controller clock so that it can

monitor the timing of the micro-controller. Therefore, a separate oscillator is necessary.

This oscillator is integrated in the L9779WD-SPI and provides a clock CLK1 for the

monitoring module. Clocked with CLK1, a divider generates the base time of 101*1/f_clk =

101 * 1/64kHz = 1.58 ms for the response-time and 8 * 101*1/64kHz =8* 1.58 ms = 12.6 ms

for the fixed time window. Accuracy of CLK1 is ±5% (or better).

The response-time is adjustable by the controller in the range 0ms to about 100ms (register

RESPTIME). The response-time can be calculated with the equation response-

time=(1+101*RESPTIME)*1/f_clk (where f_CLK depends on CONFIG6 bit1 value: if High -

default- f_clk = 64 kHz, if Low f_clk = 39 kHz).

The RESPTIME register is set to '0011 1111'b after a reset. The ERROR COUNTER is

incremented by one if the controller changes the response-time. If the response-time is set

Table 52. Reset behaviour

Component:

Reset Condition:

ERROR COUNTER

110b

‚0‘

Maximum value: 0011 1111b

timer state

“000...00”

L9779WD-SPI Datasheet(PDF) 106 Page - STMicroelectronics

L9779WD-SPI Datasheet(HTML) 106 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL