| Electronic Components Datasheet Search |
|
ADIS16475-1/PCBZ Datasheet(PDF) 14 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
ADIS16475-1/PCBZ Datasheet(HTML) 14 Page - Analog Devices |
|
14 / 37 page ![]() ADIS16475 Data Sheet Rev. D | Page 14 of 37 SERIAL PERIPHERAL INTERFACE (SPI) The SPI provides access to the user registers (see Table 8). Figure 25 shows the most common connections between the ADIS16475 and a SPI master device, which is often an embedded processor that has a SPI-compatible interface. In this example, the SPI master uses an interrupt service routine to collect data every time the data ready (DR) signal pulses. Additional information on the ADIS16475 SPI can be found in the Serial Port Operation section of this data sheet. CS SYSTEM PROCESSOR SPI MASTER VDD I/O LINES ARE COMPATIBLE WITH 3.3V LOGIC LEVELS SCLK DIN DR DOUT SS SCLK MOSI IRQ MISO ADIS16475 +3.3V Figure 25. Electrical Connection Diagram Table 6. Generic SPI Master Pin Names and Functions Mnemonic Function SS Slave select SCLK Serial clock MOSI Master output, slave input MISO Master input, slave output IRQ Interrupt request Embedded processors typically use control registers to configure their serial ports for communicating with SPI slave devices such as the ADIS16475. Table 7 provides a list of settings that describe the SPI protocol of the ADIS16475. The initialization routine of the master processor typically establishes these settings using firmware commands to write them into the control registers. Table 7. Generic Master Processor SPI Settings Processor Setting Description Master ADIS16475 operates as slave SCLK ≤ 2 MHz1 Maximum serial clock rate SPI Mode 3 CPOL = 1 (polarity), CPHA = 1 (phase) MSB First Mode Bit sequence, see Figure 30 for coding 16-Bit Mode Shift register and data length 1 A burst mode read requires this value to be ≤1 MHz (see Table 2 for more information). DATA READY (DR) The factory default configuration provides users with a DR signal on the DR pin (see Table 5), which pulses when the output data registers are updating. Connect the DR pin to a pin on the embedded processor, which triggers data collection, on the second edge of this pulse. The MSC_CTRL register, Bit 0 (see Table 105), controls the polarity of this signal. In Figure 26, Register MSC_CTRL, Bit 0 = 1, which means that data collection must start on the rising edges of the DR pulses. DR ACTIVE INACTIVE Figure 26. Data Ready When Register MSC_CTRL, Bit 0 = 1 (Default) During the start-up and reset recovery processes, the DR signal may exhibit some transient behavior before data production begins. Figure 27 shows an example of the DR behavior during startup, and Figure 28 and Figure 29 provide examples of the DR behavior during recovery from reset commands. VDD DR START-UP TIME TIME THAT VDD > 3V PULSING INDICATES DATA PRODUCTION Figure 27. Data Ready Response During Startup DR RESET RECOVERY TIME SOFTWARE RESET COMMAND GLOB_CMD[7] = 1 DR PULSING RESUMES Figure 28. Data Ready Response During Reset (Register GLOB_CMD, Bit 7 = 1) Recovery DR RST RESET RECOVERY TIME RST PIN RELEASED DR PULSING RESUMES Figure 29. Data Ready Response During Reset (RST = 0) Recovery |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |