Electronic Components Datasheet Search
  New Zealand  ▼
ALLDATASHEET.CO.NZ

X  

ADIS16475-1/PCBZ Datasheet(PDF) 15 Page - Analog Devices

Part # ADIS16475-1/PCBZ
Description  Precision, Miniature MEMs IMU
PDF  37 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  AD [Analog Devices]
Direct Link  http://www.analog.com
Logo AD - Analog Devices

ADIS16475-1/PCBZ Datasheet(HTML) 15 Page - Analog Devices

Back Button ADIS16475-1/PCBZ Datasheet HTML 11Page - Analog Devices ADIS16475-1/PCBZ Datasheet HTML 12Page - Analog Devices ADIS16475-1/PCBZ Datasheet HTML 13Page - Analog Devices ADIS16475-1/PCBZ Datasheet HTML 14Page - Analog Devices ADIS16475-1/PCBZ Datasheet HTML 15Page - Analog Devices ADIS16475-1/PCBZ Datasheet HTML 16Page - Analog Devices ADIS16475-1/PCBZ Datasheet HTML 17Page - Analog Devices ADIS16475-1/PCBZ Datasheet HTML 18Page - Analog Devices ADIS16475-1/PCBZ Datasheet HTML 19Page - Analog Devices Next Button
Zoom Inzoom in Zoom Outzoom out
 15 / 37 page
background image
Data Sheet
ADIS16475
Rev. D | Page 15 of 37
R/W
R/W
A6
A5
A4
A3
A2
A1
A0
DC7
DC6
DC5
DC4
DC3
DC2
DC1
DC0
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
CS
SCLK
DIN
DOUT
A6
A5
D13
D14
D15
NOTES
1. DOUT BITS ARE PRODUCED ONLY WHEN THE PREVIOUS 16-BIT DIN SEQUENCE STARTS WITH R/W = 0.
2. WHEN CS IS HIGH, DOUT IS IN A THREE-STATE, HIGH IMPEDANCE MODE, WHICH ALLOWS MULTIFUNCTIONAL USE OF THE LINE
FOR OTHER DEVICES.
Figure 30. SPI Communication Bit Sequence
CS
1
2
3
11
SCLK
DIN
DOUT
0x6800
DIAG_STAT
XGYRO_OUT
CHECKSUM
Figure 31. Burst Read Sequence
CS
SCLK
DIN
DOUT
DIN = 0x7200 = 0111 0010 0000 0000
DOUT = 0100 0000 0101 1011 = 0x405B = 16475 (PROD_ID)
HIGH-Z
HIGH-Z
Figure 32. SPI Signal Pattern Showing a Read of the PROD_ID Register
READING SENSOR DATA
Reading a single register requires two 16-bit cycles on the SPI:
one to request the contents of a register and another to receive
those contents. The 16-bit command code (see Figure 30) for a
read request on the SPI has three parts: the read bit (R/W = 0),
either address of the register, [A6:A0], and eight don’t care bits,
[DC7:DC0]. Figure 33 shows an example that includes two register
reads in succession. This example starts with DIN = 0x0C00 to
request the contents of the Z_GYRO_LOW register, and
follows with 0x0E00 to request the contents of the Z_GYRO_OUT
register. The sequence in Figure 33 also shows full duplex mode
of operation, which means that the ADIS16475 can receive
requests on DIN while also transmitting data out on DOUT
within the same 16-bit SPI cycle.
DIN
DOUT
0x0C00
0x0E00
NEXT
ADDRESS
Z_GYRO_LOW
Z_GYRO_OUT
Figure 33. SPI Read Example
Figure 32 provides an example of the four SPI signals when
reading the PROD_ID register (see Table 121) in a repeating
pattern. This pattern can be helpful when troubleshooting the
SPI interface setup and communications because the signals are
the same for each 16-bit sequence, except during the first cycle.
Burst Read Function
The burst read function provides a way to read a batch of
output data registers, using a continuous stream of bits, at a
rate of up to 1 MHz (SCLK). This method does not require a
stall time between each 16-bit segment (see Figure 3). As shown
in Figure 31, start this mode by setting DIN = 0x6800, and then
read each of the registers in the sequence out of DOUT while
keeping CS low for the entire 176-bit sequence.
The sequence of registers (and checksum value) in the burst read
response depends on which sample clock mode that the ADIS16475
is operating in (Register MSC_CTRL, Bits[4:2], see Table 105). In
all clock modes, except when operating in scaled sync mode
(Register MSC_CTRL, Bits[4:2] = 010), the burst read response
includes the following registers and value: DIAG_STAT,
X_GYRO_OUT, Y_GYRO_OUT, Z_GYRO_OUT, X_ACCL_
OUT, Y_ACCL_OUT, Z_ACCL_OUT, TEMP_OUT, DATA_
CNTR, and the checksum value. In these cases, use the following
formula to verify the checksum value, treating each byte in the
formula as an independent, unsigned, 8-bit number:
Checksum = DIAG_STAT, Bits[15:8] + DIAG_STAT, Bits[7:0] +
X_GYRO_OUT, Bits[15:8] + X_GYRO_OUT, Bits[7:0] +
Y_GYRO_OUT, Bits[15:8] + Y_GYRO_OUT, Bits[7:0] +
Z_GYRO_OUT, Bits[15:8] + Z_GYRO_OUT, Bits[7:0] +
X_ACCL_OUT, Bits[15:8] + X_ACCL_OUT, Bits[7:0] +
Y_ACCL_OUT, Bits[15:8] + Y_ACCL_OUT, Bits[7:0] +
Z_ACCL_OUT, Bits[15:8] + Z_ACCL_OUT, Bits[7:0] +
TEMP_OUT, Bits[15:8] + TEMP_OUT, Bits[7:0] +
DATA_CNTR, Bits[15:8] + DATA_CNTR, Bits[7:0]



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com