Electronic Components Datasheet Search
  New Zealand  ▼
ALLDATASHEET.CO.NZ

X  

PPC440EPX-SPAFFFTS Datasheet(PDF) 57 Page - Applied Micro Circuits Corporation

Part # PPC440EPX-SPAFFFTS
Description  PowerPC 440EPx Embedded Processor
PDF  94 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  AMCC [Applied Micro Circuits Corporation]
Direct Link  http://www.amcc.com
Logo AMCC - Applied Micro Circuits Corporation

PPC440EPX-SPAFFFTS Datasheet(HTML) 57 Page - Applied Micro Circuits Corporation

Back Button PPC440EPX-SPAFFFTS Datasheet HTML 53Page - Applied Micro Circuits Corporation PPC440EPX-SPAFFFTS Datasheet HTML 54Page - Applied Micro Circuits Corporation PPC440EPX-SPAFFFTS Datasheet HTML 55Page - Applied Micro Circuits Corporation PPC440EPX-SPAFFFTS Datasheet HTML 56Page - Applied Micro Circuits Corporation PPC440EPX-SPAFFFTS Datasheet HTML 57Page - Applied Micro Circuits Corporation PPC440EPX-SPAFFFTS Datasheet HTML 58Page - Applied Micro Circuits Corporation PPC440EPX-SPAFFFTS Datasheet HTML 59Page - Applied Micro Circuits Corporation PPC440EPX-SPAFFFTS Datasheet HTML 60Page - Applied Micro Circuits Corporation PPC440EPX-SPAFFFTS Datasheet HTML 61Page - Applied Micro Circuits Corporation Next Button
Zoom Inzoom in Zoom Outzoom out
 57 / 94 page
background image
440EPx – PPC440EPx Embedded Processor
Revision 1.26 – October 15, 2007
AMCC Proprietary
57
Preliminary Data Sheet
Table 8. Signal Functional Description (Sheet 1 of 9)
Notes:
1. Receiver input has hysteresis
2. Must pull up (recommended value is 3k
Ω to OV
DD (EOVDD for Ethernet)
3. Must pull down (recommended value is 1k
Ω)
4. If not used, must pull up (recommended value is 3k
Ω to OV
DD (EOVDD for Ethernet)
5. If not used, must pull down (recommended value is 1k
Ω)
6. Strapping input during reset; pull-up or pull-down required
Signal Name
Description
I/O
Type
Notes
PCI Interface
PCIAD00:31
Address/Data bus (bidirectional).
I/O
3.3V PCI
PCIC0:3/BE0:3
PCI Command/Byte Enables
.
I/O
3.3V PCI
PCIClk
Provides timing to the PCI interface for PCI transactions.
I
3.3V PCI
1, 5
PCIDevSel
Indicates the driving device has decoded its address as the
target of the current access.
(PCI 2.2 specification requires 8.2K
Ω pull up on host system)
I/O
3.3V PCI
PCIFrame
Driven by the current master to indicate beginning and duration
of an access.
(PCI 2.2 specification requires 8.2K
Ω pull up on host system)
I/O
3.3V PCI
PCIGnt0/Req
Indicates that the specified agent is granted access to the bus.
When the internal arbiter is enabled, output is PCIGnt0. When
the internal arbiter is disabled, output is Req.
(PCI 2.2 specification requires 8.2K
Ω pull up on host system)
O
3.3V PCI
PCIGnt1:5
Indicates that the specified agent is granted access to the bus.
Used only when internal PCI arbiter enabled.
O
3.3V PCI
PCIIDSel
Used as a chip select during configuration read and write
transactions.
I
3.3V PCI
PCIINT
Level sensitive PCI interrupt.
O
3.3V PCI
PCIIRDY
Indicates initiating agent’s ability to complete the current data
phase of the transaction.
(PCI 2.2 specification requires 8.2K
Ω pull up on host system)
I/O
3.3V PCI
PCIPar
Even parity.
I/O
3.3V PCI
PCIPErr
Reports data parity errors during all PCI transactions except a
Special Cycle.
(PCI 2.2 specification requires 8.2K
Ω pull up on host system)
I/O
3.3V PCI
PCIReq0/Gnt
Indicates to the PCI arbiter that the specified agent wishes to use
the bus. When the internal arbiter is enabled, input is PCIReq0.
When internal arbiter is disabled, input is Gnt.
I
3.3V PCI
1, 4
PCIReq1:5
An indication to the PCI arbiter that the specified agent wishes to
use the bus. Used only when internal PCI arbiter enabled.
I
3.3V PCI
1, 4
PCIReset
Brings PCI device registers and logic to a consistent state.
O
3.3V PCI
PCISErr
Reports address parity errors, data parity errors on the Special
Cycle command, or other catastrophic system errors.
(PCI 2.2 specification requires 8.2K
Ω pull up on host system)
I/O
3.3V PCI
PCIStop
Indicates the current target is requesting the master to stop the
current transaction.
(PCI 2.2 specification requires 8.2K
Ω pull up on host system)
I/O
3.3V PCI
PCITRDY
Indicates the target agent’s ability to complete the current data
phase of the transaction.
(PCI 2.2 specification requires 8.2K
Ω pull up on host system)
I/O
3.3V PCI



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com