Electronic Components Datasheet Search
  New Zealand  ▼
ALLDATASHEET.CO.NZ

X  

ADS1675 Datasheet(PDF) 18 Page - Texas Instruments

Part # ADS1675
Description  4MSPS, 24-Bit Analog-to-Digital Converter
PDF  40 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  TI2 [Texas Instruments]
Direct Link  https://www.ti.com
Logo TI2 - Texas Instruments

ADS1675 Datasheet(HTML) 18 Page - Texas Instruments

Back Button ADS1675 Datasheet HTML 14Page - Texas Instruments ADS1675 Datasheet HTML 15Page - Texas Instruments ADS1675 Datasheet HTML 16Page - Texas Instruments ADS1675 Datasheet HTML 17Page - Texas Instruments ADS1675 Datasheet HTML 18Page - Texas Instruments ADS1675 Datasheet HTML 19Page - Texas Instruments ADS1675 Datasheet HTML 20Page - Texas Instruments ADS1675 Datasheet HTML 21Page - Texas Instruments ADS1675 Datasheet HTML 22Page - Texas Instruments Next Button
Zoom Inzoom in Zoom Outzoom out
 18 / 40 page
background image
ADS1675
SBAS416D – DECEMBER 2008 – REVISED AUGUST 2010
www.ti.com
DIGITAL FILTER
LOW-LATENCY DIGITAL FILTER
In
ΔΣ ADCs, the digital filter has a critical influence
The Low-Latency (LL) filter provides a fast settling
on device performance. The digital filter sets the
response
targeted
for
applications
that
need
frequency
response,
data
rate,
bandwidth,
and
high-precision measurements with minimal latency. A
settling time. Choosing to optimize some of these
good example of this type of application is a
features in a filter means that compromises must be
multiplexer that measures multiple inputs. The faster
made with other specifications. These tradeoffs
the ADC settles, the faster the measurement can
determine the applications for which the device is
complete and the multiplexer can advance to the next
best suited.
input.
The ADS1675 offers two digital filters on-chip, and
The ADS1675 LL filter supports two configurations to
allows the user to direct the output data from the
help
optimize
performance
for
these
types
of
modulator
to
either
the
Wide-Bandwidth
or
applications.
Low-Latency filter. These filters allow the user to use
The LL_CONFIG input pin selects the configuration,
one converter design to address multiple applications.
as shown in Table 3. Be sure to strobe the START
The Low-Latency path filter has minimal latency or
pin after changing the configuration. If a conversion is
settling time. This reduction is achieved by reducing
in process during a configuration change, the output
the bandwidth of the filter. This path is ideal for
data for that conversion are not valid and should be
measurements with large, quick changes on the
discarded.
inputs (for example, when using a multiplexer). The
Low-Latency characteristic allows the user to cycle
Table 3. Low-Latency Pin Configurations
through the multiplexer at high speeds.
LOW-LATENCY
The other path provides a filter with excellent
LL_CONFIG PIN
CONFIGURATION
frequency response characteristics. The passband
0
Single-cycle settling
ripple is extremely small, the transition band is very
1
Fast response
steep, and there is large stop band attenuation.
These characteristics are needed for high-resolution
The first configuration is single-cycle settling. As the
measurements of ac signals. The tradeoff here is that
name implies, this configuration allows for the filter to
settling
time
increases;
for
signal
processing,
completely settle in one conversion cycle; there is no
however, this increase is not generally a critical
need to discard data. Each data output is comprised
concern.
of
information
taken
during
only
the
previous
conversion. The DRATE[2:0] digital input pins select
The FPATH digital input pin sets the filter path
the
data
rate
for
the
Single-Cycle
Settling
selection, as shown in Table 2. Note that the START
configuration, as shown in Table 4. Note that the
pin must be strobed after a change to the filter path
START pin must be strobed after a change to the
selection or data rate. If a conversion is in process
data rate. If a conversion is in process during a data
during a filter path or data rate change, the output
rate change, the output data for that conversion are
data are not valid and should be discarded.
not valid and should be discarded.
Table 2. ADS1675 Filter Path Selection
blank
FPATH PIN
SELECTED FILTER PATH
blank
1
Low-Latency path
0
Wide-Bandwidth path
Table 4. Low-Latency Data Rates with Single-Cycle Settling Configuration
DRATE[2:0]
DATA RATE (kSPS)
SETTLING TIME, tSETTLE-LL
–3dB BANDWIDTH (kHz)(1)
000
57.80
17.375ms
556tCLK
54
001
107.53
9.375ms
300tCLK
109
010
188.68
5.375ms
172tCLK
208
011
277.78
3.625ms
116tCLK
344
(1)
The input signal aliases when its frequency exceeds fDATA/2, in accordance with the Nyquist theorem.
18
Submit Documentation Feedback
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): ADS1675



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com