| Electronic Components Datasheet Search |
|
PCMB065T-2R2MS Datasheet(PDF) 28 Page - International Rectifier |
|
|
|||||||||||||||||||||||||||||
PCMB065T-2R2MS Datasheet(HTML) 28 Page - International Rectifier |
|
28 / 47 page ![]() Dual output, 4A/Phase, Highly Integrated SupIRBuck TM Single-Input Voltage, Synchronous Buck Regulator IR3891 28 www.irf.com © 2013 International Rectifier May 08, 2013 VOUT VREF R6 R5 R4 C4 C2 C3 R3 Ve FZ1 FZ 2 FP 2 FP 3 E / A Zf ZIN Frequency Gain (dB) |H(s)| dB Fb Comp Figure 28: Type III Compensation network and its asymptotic gain plot Again, the transfer function is given by: IN f out e Z Z s H V V ) ( By replacing Zin and Zf, according to Figure 28, the transfer function can be expressed as: 4 4 3 2 3 2 3 3 2 5 5 4 4 3 3 1 1 1 1 ) ( C sR C C C C sR C C sR R R sC C sR s H (28) The compensation network has three poles and two zeros and they are expressed as follows: 0 1 P F (29) 4 4 2 2 1 C R F P (30) 2 3 3 2 3 2 3 3 2 1 2 1 C R C C C C R F P (31) 3 3 1 2 1 C R F Z (32) 5 4 5 3 4 2 2 1 2 1 R C R R C F Z (33) Cross over frequency is expressed as: o o ramp in o C L V V C R F 2 1 4 3 (34) Based on the frequency of the zero generated by the output capacitor and its ESR, relative to the crossover frequency, the compensation type can be different. Table 3 shows the compensation types for relative locations of the crossover frequency. Table 3: Different types of compensators Compensator Type FESR vs FO Typical Output Capacitor Type II FLC < FESR < FO < FS/2 Electrolytic Type III FLC < FO < FESR SP Cap, Ceramic The higher the crossover frequency is, the potentially faster the load transient response will be. However, the crossover frequency should be low enough to allow attenuation of switching noise. Typically, the control loop bandwidth or crossover frequency (Fo) is selected such that: s o F F * 1/10 ~ 1/5 The DC gain should be large enough to provide high DC-regulation accuracy. The phase margin should be greater than 45 o for overall stability. The specifications for designing channel 1: Vin = 12V Vo = 1.8V Vramp= 1.8V (This is a function of Vin, pls. see Feed-Forward section) Vref = 0.5V Lo = 2.2uH Co = 4x22uF, ESR≈3mΩ each It must be noted here that the value of the capacitance used in the compensator design must be |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |