M38B53M4-059FP datasheet(53/355 Pages) MITSUBISHI

53 / 355 page

38B5 Group User’s Manual

1-37

HARDWARE

FUNCTIONAL DESCRIPTION

RBF = 1

TSC = 1

TBE = 0

TBE = 1

TSC = 0

Transmit/Receive shift clock

(1/2—1/2048 of internal

clock or external clock)

Serial I/O2 output TxD

Serial I/O2 input RxD

Write-in signal to serial I/O2 transmit/receive

buffer register (address 001F16)

Overrun error (OE)

detection

Notes 1 : The transmit interrupt (TI) can be selected to occur either when the transmit buffer has emptied (TBE=1) or after the

transmit shift operation has ended (TSC=1), by setting transmit interrupt source selection bit (TIC) of the serial I/O2

control register.

2 : If data is written to the transmit buffer register when TSC=0, the transmit clock is generated continuously and serial

data is output continuously from the TxD pin.

3 : The receive interrupt (RI) is set when the receive buffer full flag (RBF) becomes “1.”

Receive enable signal SRDY2

qSerial I/O2

Serial I/O2 can be used as either clock synchronous or asynchro-

nous (UART) serial I/O. A dedicated timer (baud rate generator) is

also provided for baud rate generation during serial I/O2 operation.

(1) Clock Synchronous Serial I/O Mode

The clock synchronous serial I/O mode can be selected by setting

the serial I/O2 mode selection bit (b6) of the serial I/O2 control reg-

Fig. 37 Operation of clock synchronous serial I/O2 function

Fig. 36 Block diagram of clock synchronous serial I/O2

ister (address 001D16) to “1.” For clock synchronous serial I/O, the

transmitter and the receiver must use the same clock for serial I/O2

operation. If an internal clock is used, transmit/receive is started by

a write signal to the serial I/O2 transmit/receive buffer register (TB/

RB) (address 001F16).

When P57 (SCLK22) is selected as a clock I/O pin, SRDY2 output

function is invalid, and P56 (SCLK21) is used as an I/O port.

1/4

F/F

P56/SCLK21

P54/RXD

P55/TXD

P57/SRDY2/SCLK22

“0”

“1”

“0”

“1”

XIN

1/2

XCIN

“1”

“0”

P57/SRDY2/SCLK22

Serial I/O2 status register

Serial I/O2 control register

Receive buffer register

Address 001F16

Receive shift register

Receive buffer full flag (RBF)

Receive interrupt request (RI)

Clock control circuit

Shift clock

Serial I/O2 synchronous clock selection bit

Baud rate generator

Division ratio 1/(n+1)

Address 001616

BRG count source selection bit

Clock control circuit

Falling edge detector

Transmit buffer register

Data bus

Address 001F16

Shift clock

Transmit shift register shift

completion flag (TSC)

Transmit buffer empty flag (TBE)

Transmit interrupt request (TI)

Transmit interrupt source selection bit

Address 001E16

Data bus

Address 001D16

Transmit shift register

Serial I/O2 clock I/O pin selection bit

Internal system clock selection bit

BRG clock

switch bit

Serial I/O2

clock I/O pin

selection bit

M38B53M4-059FP Datasheet(PDF) 53 Page - Mitsubishi Electric Semiconductor

M38B53M4-059FP Datasheet(HTML) 53 Page - Mitsubishi Electric Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL