TDSUSBF datasheet(16/46 Pages) TEKTRONIX

16 / 46 page

Advanced Search and Mark – Highlights important events and provides convenient

previous and next buttons and mouse clicks to navigate between events of interest

effortlessly.

Embedded serial bus (I2C, SPI, RS-232/422/485, UART,

USB) decoding and triggering

The MSO/DPO70000 Series instruments provide integrated support for a

broad range of serial buses – I2C, SPI, RS-232/422/485/UART, and USB.

This support for up to 16 separate serial buses enables you to monitor or

debug subsystems and components, such as frequency synthesizers, D/A

converters, and Flash Memory that are controlled or monitored through

serial control buses. While monitoring or debugging these serial buses

alone is relatively easy, decoding events on the serial bus can also enable

more complex system-level debugging. When you experience an issue with

a higher-speed serial interface, the clue to what is going wrong may be

found by using the serial bus decode feature to observe the data on your

I2C, SPI, RS-232/422/485/UART, or USB interface.

Probing – analog and digital

Often the biggest challenge in debugging a system is getting access to the

required signals. Tektronix offers a wide array of probing solutions,

including the P7700, P7600, and P7500 TriMode™ probing system with

bandwidths that are perfectly matched to the MSO/DPO70000 Series.

These TriMode™ probes allow you to switch among differential, single

ended, and common-mode measurements without moving the probe from

its connection points. The P7700 and P7500 series are compatible with all

DPO/MSO70000C/DX/SX models. The P7600 series is compatible with

DPO/MSO70000 DX/SX models, and combines low noise, 33 GHz

bandwidth and the convenience of TriMode™ probing. The P7500 Series

offers probes with performance from 4 GHz to 25 GHz and offers several

low-cost solder tips with quick connection features that allow moving the

probe to various solder points fast and easy.

The low-cost solder tips available for the P7500 TriMode™ probes allow quick connection

so moving the probe to various solder points is fast and easy.

On the MSO70000 Series, the P6780 differential, P6750 high-density D-

Max®, and P6717A general-purpose logic probes provide connectivity to

low-speed and high-speed digital signals with low loading, small size, and a

range of accessories for soldering or browsing.

Solder tip accessories designed for the P6780 differential logic probes provide access to

signals on tightly spaced vias and fine-pitched components.

DPO7OE Series Optical Probes

The DPO7OE Series Optical probes can be used as an Optical Reference

Receiver for high speed serial data signals (using selectable Bessel-

Thomson ORR filters), or can be used as a conventional O/E converter for

general wide-bandwidth optical signal acquisition. The DPO7OE Series

(DPO7OE1 and DPO7OE2) probes are compatible with DPO/MSO70000

C/DX/SX models. Connected to TekConnect channels for up to 33 GHz

bandwidth.

Datasheet

16 www.tek.com

TDSUSBF Datasheet(PDF) 16 Page - TEKTRONIX, INC.

TDSUSBF Datasheet(HTML) 16 Page - TEKTRONIX, INC.

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46

Datasheet Download

Link URL