ADSP-21469KBZ-ENG2 datasheet(7/56 Pages) AD

7 / 56 page

ADSP-21469/ADSP-21469W

Preliminary Technical Data

Rev. PrB

Page 7 of 56

November 2008

to four separate devices to coexist, supporting any desired com-

bination of synchronous and asynchronous device types. Non

DDR2 DRAM external memory address space is shown in

Table 4.

External Memory Execution

In the ADSP-21469, the program sequencer can execute code

directly from external memory bank 0 (SRAM, as well as DDR2

DRAM). This allows more options to a user in terms of code

and data storage. With external execution, programs run at

slower speeds since 48-bit instructions are fetched in parts from

a 16-bit external bus coupled with the inherent latency of fetch-

ing instructions from DDR2 DRAM. VISA mode and SIMD

mode accesses are supported for DDR2 space. However, exter-

nal memory execution from DDR2 space is different for VISA

and non-VISA mode.

DDR2 Support

The ADSP-21469 supports a 16-bit DDR interface operating at a

maximum frequency of half the core clock. Execution from

external memory is supported. External memory up to 2 Gbits

can be supported. Delay line DMA functionality supported.

DDR2 DRAM Controller

The DDR2 DRAM controller provides an 16-bit interface to up

to four separate banks of industry-standard DDR2 DRAM

devices. Fully compliant with the DDR2 DRAM standard, each

bank can has its own memory select line (DDR2_CS3-

DDR2_CS0), and can be configured to contain between 32M

bytes and 256M bytes of memory. DDR2 DRAM external mem-

ory address space is shown in Table 5

A set of programmable timing parameters is available to config-

ure the DDR2 DRAM banks to support memory devices.

Note that the external memory bank addresses shown are for

normal-word (32-bit) accesses. If 48-bit instructions as well as

32-bit data are both placed in the same external memory bank,

care must be taken while mapping them to avoid overlap. In

case of 32-bit wide external memory, two 48-bit instructions

will be stored in three 32-bit wide memory locations. For exam-

ple, if 2k instructions are placed in 32-bit wide external memory

starting at the bank 0 normal-word base address 0x0030 0000

(corresponding to instruction address 0x0020 0000) and ending

at address 0x0030 0BFF (corresponding to instruction address

0x0020 07FF), then data buffers can be placed starting at an

address that is offset by 3k 32-bit words (for example, starting at

0x0030 0C00).

Asynchronous Memory Controller

The asynchronous memory controller provides a configurable

interface for up to four separate banks of memory or I/O

devices. Each bank can be independently programmed with dif-

ferent timing parameters, enabling connection to a wide variety

of memory devices including SRAM, flash, and EPROM, as well

as I/O devices that interface with standard memory control

lines. Bank 0 occupies a 14M word window and banks 1, 2, and

3 occupy a 16M word window in the processor’s address space

but, if not fully populated, these windows are not made contigu-

ous by the memory controller logic.

The asynchronous memory controller is capable of a maximum

throughput of TBD Mbps using a TBD MHz external bus speed.

Other features include 8 to 32-bit packing and unpacking, boot-

ing from bank select 1, and support for delay line DMA.

Shared External Memory

The ADSP-21469 processor supports connecting to common

shared external DDR2 memory with other ADSP-21469 proces-

sors to create shared external bus processor systems. This

support includes:

• Distributed, on-chip arbitration for the shared external bus

• Fixed and rotating priority bus arbitration

• Bus time-out logic

• Bus lock

Multiple processors can share the external bus with no addi-

tional arbitration logic. Arbitration logic is included on-chip to

allow the connection of up to TBD processors.

Bus arbitration is accomplished through the BR6-1 signals and

the priority scheme for bus arbitration is determined by the set-

ting of the RPBA pin. Table 6 on Page 12 provides descriptions

of the pins used in multiprocessor systems.

INPUT/OUTPUT FEATURES

The ADSP-21469 I/O processor provides 36 channels of DMA,

as well as an extensive set of peripherals. These include a 20 lead

digital applications interface, which controls:

• Eight serial ports

• S/PDIF receiver/transmitter

Table 4. External Memory for Non DDR2 DRAM Addresses

Bank

Size in

Words

Address Range

Bank 0

14M

0x0020 0000 – 0x00FF FFFF

Bank 1

16M

0x0400 0000 – 0x04FF FFFF

Bank 2

16M

0x0800 0000 – 0x08FF FFFF

Bank 3

16M

0x0C00 0000 – 0x0CFF FFFF

Table 5. External Memory for DDR2 DRAM Addresses

Bank

Size in

Words

Address Range

Bank 0

62M

0x0020 0000 – 0x03FF FFFF

Bank 1

64M

0x0400 0000 – 0x07FF FFFF

Bank 2

64M

0x0800 0000 – 0x0BFF FFFF

Bank 3

64M

0x0C00 0000 – 0x0FFF FFFF

ADSP-21469KBZ-ENG2 Datasheet(PDF) 7 Page - Analog Devices

ADSP-21469KBZ-ENG2 Datasheet(HTML) 7 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56

Datasheet Download

Link URL