PIC16F1526 datasheet(172/354 Pages) MICROCHIP

172 / 354 page

PIC16(L)F1526/27

DS41458A-page 172

Preliminary

 2011 Microchip Technology Inc.

18.6.6

TIMER1/3/5 GATE EVENT

INTERRUPT

When Timer1/3/5 Gate Event Interrupt is enabled, it is

possible to generate an interrupt upon the completion

of a gate event. When the falling edge of TxGVAL

occurs, the TMRxGIF flag bit in the PIR1 register will be

set. If the TMRxGIE bit in the PIE1 register is set, then

an interrupt will be recognized.

The TMRxGIF flag bit operates even when the

Timer1/3/5 gate is not enabled (TMRxGE bit is

cleared).

18.7

Timer1/3/5 Interrupt

The Timer1/3/5 register pair (TMRxH:TMRxL) incre-

ments to FFFFh and rolls over to 0000h. When

Timer1/3/5 rolls over, the Timer1/3/5 interrupt flag bit of

the PIR1 register is set. To enable the interrupt on roll-

over, you must set these bits:

• TMRxON bit of the TxCON register

• TMRxIE bit of the PIE1 register

• PEIE bit of the INTCON register

• GIE bit of the INTCON register

The interrupt is cleared by clearing the TMRxIF bit in

the Interrupt Service Routine.

18.8

Timer1/3/5 Operation During Sleep

Timer1/3/5 can only operate during Sleep when setup

in Asynchronous Counter mode. In this mode, an exter-

nal crystal or clock source can be used to increment the

counter. To set up the timer to wake the device:

• TMRxON bit of the TxCON register must be set

• TMRxIE bit of the PIE1 register must be set

• PEIE bit of the INTCON register must be set

• TxSYNC bit of the TxCON register must be set

• TMRxCS bits of the TxCON register must be

configured

• SOSCEN bit of the TxCON register must be

configured

The device will wake-up on an overflow and execute

the next instructions. If the GIE bit of the INTCON

Routine.

Timer1/3/5 oscillator will continue to operate in Sleep

regardless of the TxSYNC bit setting.

18.9

ECCP/CCP Capture/Compare Time

Base

The CCP module uses the TMRxH:TMRxL register pair

as the time base when operating in Capture or Com-

pare mode.

In Capture mode, the value in the TMRxH:TMRxL

In Compare mode, an event is triggered when the value

CCPR1H:CCPR1L register pair matches the value in

the TMRxH:TMRxL register pair. This event can be a

Special Event Trigger.

For

information,

see

Section 20.0

“Capture/Compare/PWM Modules”

18.10 ECCP/CCP Special Event Trigger

When the CCP is configured to trigger a special event,

the trigger will clear the TMRxH:TMRxL register pair.

This special event does not cause a Timer1/3/5 inter-

rupt. The CCP module may still be configured to gener-

ate a CCP interrupt.

In this mode of operation, the CCPR1H:CCPR1L

Timer1/3/5.

Timer1/3/5 should be synchronized and FOSC/4 should

be selected as the clock source in order to utilize the

Special Event Trigger. Asynchronous operation of

Timer1/3/5 can cause a Special Event Trigger to be

missed.

In the event that a write to TMRxH or TMRxL coincides

with a Special Event Trigger from the CCP, the write will

take precedence.

For more information, see Section 16.2.5 “Special

Event Trigger”

Note:

The TMRxH:TMRxL register pair and the

TMRxIF bit should be cleared before

enabling interrupts.

PIC16F1526 Datasheet(PDF) 172 Page - Microchip Technology

PIC16F1526 Datasheet(HTML) 172 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL