ST25R3916B datasheet(37/165 Pages) STMICROELECTRONICS

37 / 165 page

DS13541 Rev 7

37/165

ST25R3916B ST25R3917B

Application information

164

If the External field level is not detected yet, the Activation threshold is used. If the External

field level is detected, the Deactivation threshold is used.

The Activation threshold must be set higher than or equal to the Deactivation threshold.

If the Activation is higher than the Deactivation, the hysteresis is given by the difference

between the two levels.

If the Activation and Deactivation levels are equal, there is no the hysteresis in the system

and multiple field-on/off events can verify if the actual field level persists in proximity of the

selected threshold.

Peer detection threshold

This threshold is used to detect the field emitted by peer NFC device with whom NFC

communication is going on. It can be selected in the range from 75 to 800 mVPP. When this

threshold is enabled the detector is in low power mode. An interrupt is generated when an

external field is detected and also when it is switched off. With such implementation it can

also be used to detect the moment when the external field disappears. This can be used to

detect the moment when the peer NFC device (either an initiator or a target) has stopped

emitting an RF field.

The External Field Detector is enabled in low power Peer Detection mode by setting bits

en_fd_c,1:0> in the Operation control register.

Collision avoidance threshold

This threshold is used during the RF collision avoidance sequence, which is executed by

sending NFC Field ON commands (see Section 4.4.5: NFC field ON commands). It can be

selected in the range from 25 to 800 mVPP.

4.2.10

Power supply system

The ST25R3916B and ST25R3917B feature three positive supply pins, VDD, VDD_TX and

VDD_IO:

•

VDD is the main power supply pin. It supplies the ST25R3916B and ST25R3917B

blocks through two regulators (VDD_A, VDD_D)

•

VDD_TX is the transmitter supply pin. It supplies the transmitter via two regulators

(VDD_RF, VDD_AM). VDD range from 2.4 to 5.5 V is supported. VDD and VDD_TX must

be connected to the same power supply.

•

VDD_IO is used to define supply level for digital communication pins (BSS, MISO,

MOSI, SCLK, IRQ, MCU_CLK). Digital communication pins interface to the

ST25R3916B and ST25R3917B logic through level shifters, therefore the internal

supply voltage can be either higher or lower than VDD_IO. VDD_IO range from 1.65 to

5.5 V is supported.

Figure 10 details the building blocks of the ST25R3916B and ST25R3917B power supply

system. It contains three regulators, a power-down support block, a block generating

analogue reference voltage (AGDC) and a block performing automatic power supply

adjustment procedure. The three regulators are providing supply to analogue blocks

(VDD_A), logic (VDD_D) and transmitter (VDD_RF). The use of VDD_A and VDD_D regulators is

mandatory at 5 V power supply to provide regulated voltage to analogue and logic blocks,

which only use 3.3 V. The use of VDD_A and VDD_D regulators at 3 V supply and VDD_RF

regulator at any supply voltage is recommended to improve system PSRR.

ST25R3916B Datasheet(PDF) 37 Page - STMicroelectronics

ST25R3916B Datasheet(HTML) 37 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL