| Electronic Components Datasheet Search |
|
PIC32MM0016GPL028 Datasheet(PDF) 20 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
PIC32MM0016GPL028 Datasheet(HTML) 20 Page - Microchip Technology |
|
20 / 268 page ![]() PIC32MM0064GPL036 FAMILY DS60001324B-page 20 2015-2016 Microchip Technology Inc. FIGURE 2-1: RECOMMENDED MINIMUM CONNECTION 2.2.1 BULK CAPACITORS The use of a bulk capacitor is recommended to improve power supply stability. Typical values range from 4.7 µF to 47 µF. This capacitor should be located as close to the device as possible. 2.3 Master Clear (MCLR) Pin The MCLR pin provides for two specific device functions: •Device Reset • Device Programming and Debugging Pulling The MCLR pin low generates a device Reset. Figure 2-2 illustrates a typical MCLR circuit. During device programming and debugging, the resistance and capacitance that can be added to the pin must be considered. Device programmers and debuggers drive the MCLR pin. Consequently, specific voltage levels (VIH and VIL) and fast signal transitions must not be adversely affected. Therefore, specific values of R and C will need to be adjusted based on the application and PCB requirements. For example, as illustrated in Figure 2-2, it is recommended that the capacitor, C, be isolated from the MCLR pin during programming and debugging operations. Place the components illustrated in Figure 2-2 within one-quarter inch (6 mm) from the MCLR pin. FIGURE 2-2: EXAMPLE OF MCLR PIN CONNECTIONS(1,2,3) 2.4 Capacitor on Internal Voltage Regulator (VCAP) A low-ESR (<1 Ohm) capacitor is required on the VCAP pin, which is used to stabilize the internal voltage regu- lator output. The VCAP pin must not be connected to VDD and must have a CEFC capacitor, with at least a 6V rating, connected to ground. The type can be ceramic or tantalum. The recommended value of the CEFC capacitor is 10 μF. On the printed circuit board, it should be placed as close to the VCAP pin as possible. If the board is experiencing high-frequency noise, upward of tens of MHz, add a second ceramic-type capacitor in parallel to this capacitor. The value of the second capacitor can be in the range of 0.01 μF to 0.001 μF. PIC32 VDD VSS VSS VDD 0.1 µF Ceramic 0.1 µF Ceramic 0.1 µF Ceramic 0.1 µF Ceramic C R VDD MCLR 0.1 µF Ceramic R1 CEFC 10 µF Note 1: 470 R1 1 k will limit any current flowing into MCLR from the external capacitor, C, in the event of MCLR pin breakdown, due to Electrostatic Discharge (ESD) or Electrical Overstress (EOS). Ensure that the MCLR pin VIH and VIL specifications are met without interfering with the debug/programmer tools. 2: The capacitor can be sized to prevent unintentional Resets from brief glitches or to extend the device Reset period during POR. 3: No pull-ups or bypass capacitors are allowed on active debug/program PGECx/PGEDx pins. R1(1) 10k VDD MCLR PIC32 1 k 0.1 µF(2) PGECx(3) PGEDx(3) 1 5 4 2 3 6 VDD VSS NC R C |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |