| Electronic Components Datasheet Search |
|
PIC32MM0016GPL028 Datasheet(PDF) 39 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
PIC32MM0016GPL028 Datasheet(HTML) 39 Page - Microchip Technology |
|
39 / 268 page ![]() 2015-2016 Microchip Technology Inc. DS60001324B-page 39 PIC32MM0064GPL036 FAMILY REGISTER 5-1: NVMCON: NVM PROGRAMMING CONTROL REGISTER Bit Range Bit 31/23/15/7 Bit 30/22/14/6 Bit 29/21/13/5 Bit 28/20/12/4 Bit 27/19/11/3 Bit 26/18/10/2 Bit 25/17/9/1 Bit 24/16/8/0 31:24 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — 23:16 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — 15:8 R/W-0, HC R/W-0 R-0, HS, HC R-0, HS, HC r-0 U-0 U-0 U-0 WR(1,4) WREN(1) WRERR(1,2) LVDERR(1,2) — — — — 7:0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 — — — —NVMOP<3:0>(3) Legend: HS = Hardware Settable bit HC = Hardware Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared r = Reserved bit bit 31-16 Unimplemented: Read as ‘0’ bit 15 WR: Write Control bit(1,4) This bit cannot be cleared and can be set only when WREN = 1, and the unlock sequence has been performed. 1 = Initiates a Flash operation 0 = Flash operation is complete or inactive bit 14 WREN: Write Enable bit(1) 1 = Enables writes to the WR bit and disables writes to the NVMOP<3:0> bits 0 = Disables writes to the WR bit and enables writes to the NVMOP<3:0> bits bit 13 WRERR: Write Error bit(1,2) This bit can be cleared only by setting the NVMOP<3:0> bits = 0000 and initiating a Flash operation. 1 = Program or erase sequence did not complete successfully 0 = Program or erase sequence completed normally bit 12 LVDERR: Low-Voltage Detect Error bit(1,2) This bit can be cleared only by setting the NVMOP<3:0> bits = 0000 and initiating a Flash operation. 1 = Low voltage is detected (possible data corruption if WRERR is set) 0 = Voltage level is acceptable for programming bit 11 Reserved: Maintain as ‘0’ bit 10-4 Unimplemented: Read as ‘0’ Note 1: These bits are only reset by a Power-on Reset (POR) and are not affected by other Reset sources. 2: These bits are cleared by setting NVMOP<3:0> = 0000 and initiating a Flash operation (i.e., WR). 3: NVMOP<3:0> bits are write-protected if the WREN bit is set. 4: Writes to the WR bit require an unlock sequence. Refer to Section 5.1 “Flash Controller Registers Write Protection” for details. |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |