Electronic Components Datasheet Search
  New Zealand  ▼
ALLDATASHEET.CO.NZ

X  

LM5064PMH/NOPB Datasheet(PDF) 17 Page - Texas Instruments

Part # LM5064PMH/NOPB
Description  LM5064 Negative Voltage System Power Management and Protection IC with PMBus
PDF  64 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  TI2 [Texas Instruments]
Direct Link  https://www.ti.com
Logo TI2 - Texas Instruments

LM5064PMH/NOPB Datasheet(HTML) 17 Page - Texas Instruments

Back Button LM5064PMH/NOPB Datasheet HTML 13Page - Texas Instruments LM5064PMH/NOPB Datasheet HTML 14Page - Texas Instruments LM5064PMH/NOPB Datasheet HTML 15Page - Texas Instruments LM5064PMH/NOPB Datasheet HTML 16Page - Texas Instruments LM5064PMH/NOPB Datasheet HTML 17Page - Texas Instruments LM5064PMH/NOPB Datasheet HTML 18Page - Texas Instruments LM5064PMH/NOPB Datasheet HTML 19Page - Texas Instruments LM5064PMH/NOPB Datasheet HTML 20Page - Texas Instruments LM5064PMH/NOPB Datasheet HTML 21Page - Texas Instruments Next Button
Zoom Inzoom in Zoom Outzoom out
 17 / 64 page
background image
LM5064
Shutdown
Control
VCC
UVLO
OVLO
VEE
R1
R2
R3
VSYS
LM5064
www.ti.com
SNVS718E – JUNE 2011 – REVISED FEBRUARY 2013
Over-Voltage Lockout (OVLO)
The series pass MOSFET (Q1) is enabled when the input supply voltage (VSYS) is within the operating range
defined by the programmable under-voltage lockout (UVLO) and over-voltage lockout (OVLO) levels. If VSYS
raises the OVLO pin voltage above its threshold (2.47V above VEE), Q1 is switched off by the 4.1 mA pull-down
current at the GATE pin, denying power to the load. When the OVLO pin is above its threshold, the internal 21
µA current source at OVLO is switched on, raising the voltage at OVLO to provide threshold hysteresis. When
VSYS is reduced below the OVLO level Q1 is re-enabled. An OVLO condition will toggle the VIN_OV_FAULT bit in
the STATUS_INPUT (7Ch) register, the INPUT bit in the STATUS_WORD (79h) register and the
VIN_OVERVOLTAGE_FAULT bit in the DIAGNOSTIC_WORD (E1h) register. The SMBA pin will be pulled low
unless this feature is disabled using the ALERT_MASK (D8h) register.
Shutdown Control
The load current can be remotely switched off by taking the UVLO/EN pin below its threshold with an open
collector or open drain device, as shown in Figure 5. Upon releasing the UVLO/EN pin the LM5064 switches on
the load current with in-rush current and power limiting.
Figure 5. Shutdown Control
Power Good Pin
The Power Good output indicator pin (PGD) is connected to the drain of an internal N-channel MOSFET. An
external pull-up resistor is required at PGD to an appropriate voltage to indicate the status to downstream
circuitry. The off-state voltage at the PGD pin must be more positive than VEE, and can be up to 80V above VEE
with transient capability to 100V. PGD is switched high at the end of the turn-on sequence when the voltage from
OUT to SENSE (the external MOSFET’s VDS) decreases below 1.24V. PGD switches low if the MOSFET’s VDS
increases passed 2.5V, if the system input voltage goes below the UVLO threshold or above the OVLO
threshold, or if a fault is detected. However, the PGD output cannot stay low when the operating voltage (VCC-
VEE) is less than 2V.
VDD Sub-Regulator
The LM5064 contains an internal linear sub-regulator which steps down the VCC voltage to generate a 4.9V rail
(above VEE) used for powering low voltage circuitry. The VDD sub-regulator should be used as the pull-up
supply for the CL, RETRY, ADR2, ADR1, ADR0 pins if they are to be tied high. It may also be used as the pull-
up supply for the PGD and the SMBus signals (SDA, SCL, SMBA). The VDD sub-regulator is not designed to
drive high currents. Careful consideration of internal power dissipation should be practiced when VDD is loaded
with other integrated circuits. The VDD pin is current limited to 30 mA in order to protect the LM5064 in the event
of a short. The sub-regulator requires a ceramic bypass capacitance (terminated to VEE) having a value of 1 µF
or greater to be placed as close to the VDD pin as the PCB layout allows.
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Links: LM5064



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com