Electronic Components Datasheet Search
  New Zealand  ▼
ALLDATASHEET.CO.NZ

X  

EVAL-ADF7020DBZ2 Datasheet(PDF) 12 Page - Analog Devices

Part # EVAL-ADF7020DBZ2
Description  High Performance, ISM Band, FSK/ASK Transceiver IC
PDF  48 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  AD [Analog Devices]
Direct Link  http://www.analog.com
Logo AD - Analog Devices

EVAL-ADF7020DBZ2 Datasheet(HTML) 12 Page - Analog Devices

Back Button EVAL-ADF7020DBZ2 Datasheet HTML 8Page - Analog Devices EVAL-ADF7020DBZ2 Datasheet HTML 9Page - Analog Devices EVAL-ADF7020DBZ2 Datasheet HTML 10Page - Analog Devices EVAL-ADF7020DBZ2 Datasheet HTML 11Page - Analog Devices EVAL-ADF7020DBZ2 Datasheet HTML 12Page - Analog Devices EVAL-ADF7020DBZ2 Datasheet HTML 13Page - Analog Devices EVAL-ADF7020DBZ2 Datasheet HTML 14Page - Analog Devices EVAL-ADF7020DBZ2 Datasheet HTML 15Page - Analog Devices EVAL-ADF7020DBZ2 Datasheet HTML 16Page - Analog Devices Next Button
Zoom Inzoom in Zoom Outzoom out
 12 / 48 page
background image
ADF7020
Data Sheet
Rev. D | Page 12 of 48
Pin No.
Mnemonic
Description
27
SREAD
Serial Data Output. This pin is used to feed readback data from the ADF7020 to the microcontroller. The
SCLK input is used to clock each readback bit (AFC, ADC readback) from the SREAD pin.
28
SCLK
Serial Clock Input. This serial clock is used to clock in the serial data to the registers. The data is latched into
the 24-bit shift register on the CLK rising edge. This pin is a digital CMOS input.
29
GND2
Ground for Digital Section.
30
ADCIN
Analog-to-Digital Converter Input. The internal 7-bit ADC can be accessed through this pin. Full scale is 0 V
to 1.9 V. Readback is made using the SREAD pin.
31
CREG2
Regulator Voltage for Digital Block. A 100 nF in parallel with a 5.1 pF capacitor should be placed between
this pin and ground for regulator stability and noise rejection.
32
VDD2
Voltage Supply for Digital Block. A decoupling capacitor of 10 nF should be placed as close as possible to
this pin.
33
INT/LOCK
Bidirectional Pin. In output mode (interrupt mode), the ADF7020 asserts the INT/ LOCK pin when it has
found a match for the preamble sequence. In input mode (lock mode), the microcontroller can be used to
lock the demodulator threshold when a valid preamble has been detected. Once the threshold is locked,
NRZ data can be reliably received. In this mode, a demodulation lock can be asserted with minimum delay.
34
DATA I/O
Transmit Data Input/Received Data Output. This is a digital pin, and normal CMOS levels apply.
35
DATA CLK
In receive mode, the pin outputs the synchronized data clock. The positive clock edge is matched to the
center of the received data. In GFSK transmit mode, the pin outputs an accurate clock to latch the data
from the microcontroller into the transmit section at the exact required data rate. See the Gaussian
Frequency Shift Keying (GFSK) section.
36
CLKOUT
A Divided-Down Version of the Crystal Reference with Output Driver. The digital clock output can be
used to drive several other CMOS inputs, such as a microcontroller clock. The output has a 50:50 mark-
space ratio.
37
MUXOUT
This pin provides the Lock_Detect signal, which is used to determine if the PLL is locked to the correct
frequency. Other signals include Regulator_Ready, which is an indicator of the status of the serial interface
regulator.
38
OSC2
The reference crystal should be connected between this pin and OSC1. A TCXO reference can be used by
driving this pin with CMOS levels and disabling the crystal oscillator.
39
OSC1
The reference crystal should be connected between this pin and OSC2.
40
VDD3
Voltage Supply for the Charge Pump and PLL Dividers. This pin should be decoupled to ground with a
0.01 µF capacitor.
41
CREG3
Regulator Voltage for Charge Pump and PLL Dividers. A 100 nF in parallel with a 5.1 pF capacitor should be
placed between this pin and ground for regulator stability and noise rejection.
42
CPOUT
Charge Pump Output. This output generates current pulses that are integrated in the loop filter. The
integrated current changes the control voltage on the input to the VCO.
43
VDD
Voltage Supply for VCO Tank Circuit. This pin should be decoupled to ground with a 0.01 µF capacitor.
44 to 47
GND, GND1,
VCO GND
Grounds for VCO Block.
48
CVCO
A 22 nF capacitor should be placed between this pin and CREG1 to reduce VCO noise.
EP
Exposed Pad. The exposed pad must be connected to ground.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com