Electronic Components Datasheet Search
  New Zealand  ▼
ALLDATASHEET.CO.NZ

X  

EVAL-ADF7020DBZ2 Datasheet(PDF) 23 Page - Analog Devices

Part # EVAL-ADF7020DBZ2
Description  High Performance, ISM Band, FSK/ASK Transceiver IC
PDF  48 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  AD [Analog Devices]
Direct Link  http://www.analog.com
Logo AD - Analog Devices

EVAL-ADF7020DBZ2 Datasheet(HTML) 23 Page - Analog Devices

Back Button EVAL-ADF7020DBZ2 Datasheet HTML 19Page - Analog Devices EVAL-ADF7020DBZ2 Datasheet HTML 20Page - Analog Devices EVAL-ADF7020DBZ2 Datasheet HTML 21Page - Analog Devices EVAL-ADF7020DBZ2 Datasheet HTML 22Page - Analog Devices EVAL-ADF7020DBZ2 Datasheet HTML 23Page - Analog Devices EVAL-ADF7020DBZ2 Datasheet HTML 24Page - Analog Devices EVAL-ADF7020DBZ2 Datasheet HTML 25Page - Analog Devices EVAL-ADF7020DBZ2 Datasheet HTML 26Page - Analog Devices EVAL-ADF7020DBZ2 Datasheet HTML 27Page - Analog Devices Next Button
Zoom Inzoom in Zoom Outzoom out
 23 / 48 page
background image
Data Sheet
ADF7020
Rev. D | Page 23 of 48
Table 9. Register Settings1
Setting Name
Register Address
Value
Postdemod_BW_Setting
R4_DB[6:15]
0x09
Discriminator_BW
R6_DB[4:13]
0x3F
Dot_Product
R6_DB14
0
RxData_Invert
R6_DB29
1
1 The latest version of the ADF7020 configuration software can aid in
calculating register settings.
LINEAR FSK DEMODULATOR
Figure 31 shows a block diagram of the linear FSK demodulator.
SLICER
FREQUENCY
IF
LEVEL
I
Q
LIMITER
7
MUX 1
ADC RSSI OUTPUT
LINEAR DISCRIMINATOR
R4_DB[6:15]
FREQUENCY
READBACK
AND
AFC LOOP
RxDATA
Figure 31. Block Diagram of Frequency Measurement System and
ASK/OOK/Linear FSK Demodulator
This method of frequency demodulation is useful when very
short preamble length is required, and the system protocol
cannot support the overhead of the settling time of the internal
feedback AFC loop settling.
A digital frequency discriminator provides an output signal that
is linearly proportional to the frequency of the limiter outputs.
The discriminator output is then filtered and averaged using a
combined averaging filter and envelope detector. The demodu-
lated FSK data is recovered by threshold-detecting the output of
the averaging filter, (see Figure 31). In this mode, the slicer
output shown in Figure 31 is routed to the data synchronizer
PLL for clock synchronization. To enable the linear FSK
demodulator, set Bits R4_DB[4:5] to 00.
The 3 dB bandwidth of the postdemodulation filter is set in the
same way as the FSK correlator/demodulator, which is set in
R4_DB[6:15] and is defined as
CLK
DEMOD
f
Setting
BW
Postdemod
CUTOFF
_
2
2
_
_
10
where fCUTOFF is the target 3 dB bandwidth in Hz of the
postdemodulator filter. DEMOD_CLK is as defined in the
Register 3—Receiver Clock Register section, second comment.
ASK/OOK Operation
ASK/OOK demodulation is activated by setting Bits R4_DB[4:5]
to 10.
Digital filtering and envelope detecting the digitized RSSI input
via MUX 1, as shown in Figure 31, performs ASK/OOK
demodulation. The bandwidth of the digital filter must be
optimized to remove any excess noise without causing ISI in the
received ASK/OOK signal.
The 3 dB bandwidth of this filter is typically set at approximately
0.75 times the user data rate and is assigned by R4 _DB[6:15] as
CLK
DEMOD
f
Setting
BW
Postdemod
CUTOFF
_
2
2
_
_
10
where fCUTOFF is the target 3 dB bandwidth in Hz of the
postdemodulator filter.
It is also recommended to adjust the peak response factor to 6
in Register 10 for robust operation over the full input range.
This improves the receiver’s AM immunity performance.
AFC
The ADF7020 supports a real-time AFC loop, which is used to
remove frequency errors that can arise due to mismatches between
the transmit and receive crystals. This uses the frequency
discriminator block, as described in the Linear FSK Demodulator
section (see Figure 31). The discriminator output is filtered and
averaged to remove the FSK frequency modulation, using a
combined averaging filter and envelope detector. In FSK mode,
the output of the envelope detector provides an estimate of the
average IF frequency.
Two methods of AFC, external and internal, are supported on
the ADF7020 (in FSK mode only).
External AFC
The user reads back the frequency information through the
ADF7020 serial port and applies a frequency correction value to
the fractional-N synthesizer’s N divider.
The frequency information is obtained by reading the 16-bit
signed AFC_READBACK, as described in the Readback Format
section, and applying the following formula:
FREQ_RB [Hz] = (AFC_READBACK × DEMOD_CLK)/215
Note that while the AFC_READBACK value is a signed number,
under normal operating conditions, it is positive. The frequency
error can be calculated from
FREQ_Error [Hz] = FREQ_RB (Hz) − 200 kHz
Thus, in the absence of frequency errors, the FREQ_RB value is
equal to the IF frequency of 200 kHz.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com