Electronic Components Datasheet Search
  New Zealand  ▼
ALLDATASHEET.CO.NZ

X  

EVAL-ADF7020DBZ2 Datasheet(PDF) 22 Page - Analog Devices

Part # EVAL-ADF7020DBZ2
Description  High Performance, ISM Band, FSK/ASK Transceiver IC
PDF  48 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  AD [Analog Devices]
Direct Link  http://www.analog.com
Logo AD - Analog Devices

EVAL-ADF7020DBZ2 Datasheet(HTML) 22 Page - Analog Devices

Back Button EVAL-ADF7020DBZ2 Datasheet HTML 18Page - Analog Devices EVAL-ADF7020DBZ2 Datasheet HTML 19Page - Analog Devices EVAL-ADF7020DBZ2 Datasheet HTML 20Page - Analog Devices EVAL-ADF7020DBZ2 Datasheet HTML 21Page - Analog Devices EVAL-ADF7020DBZ2 Datasheet HTML 22Page - Analog Devices EVAL-ADF7020DBZ2 Datasheet HTML 23Page - Analog Devices EVAL-ADF7020DBZ2 Datasheet HTML 24Page - Analog Devices EVAL-ADF7020DBZ2 Datasheet HTML 25Page - Analog Devices EVAL-ADF7020DBZ2 Datasheet HTML 26Page - Analog Devices Next Button
Zoom Inzoom in Zoom Outzoom out
 22 / 48 page
background image
ADF7020
Data Sheet
Rev. D | Page 22 of 48
IF –
fDEV
IF +
fDEV
I
IF
Q
LIMITERS
0
R6_DB[4:13]
R3_DB[8:15]
R6_DB[14]
RxDATA
RxCLK
SLICER
FREQUENCY CORRELATOR
Figure 30. FSK Correlator/Demodulator Block Diagram
Postdemodulator Filter
A second-order, digital low-pass filter removes excess noise from
the demodulated bit stream at the output of the discriminator.
The bandwidth of this postdemodulator filter is programmable
and must be optimized for the user’s data rate. If the bandwidth
is set too narrow, performance is degraded due to intersymbol
interference (ISI). If the bandwidth is set too wide, excess noise
degrades the receiver’s performance. Typically, the 3 dB bandwidth
of this filter is set at approximately 0.75 times the user’s data rate,
using Bits R4_DB[6:15].
Bit Slicer
The received data is recovered by the threshold detecting the
output of the postdemodulator low-pass filter. In the correlator/
demodulator, the binary output signal levels of the frequency
discriminator are always centered on 0. Therefore, the slicer
threshold level can be fixed at 0, and the demodulator perform-
ance is independent of the run-length constraints of the transmit
data bit stream. This results in robust data recovery, which does
not suffer from the classic baseline wander problems that exist in
the more traditional FSK demodulators.
Frequency errors are removed by an internal AFC loop that
measures the average IF frequency at the limiter output and
applies a frequency correction value to the fractional-N
synthesizer. This loop should be activated when the frequency
errors are greater than approximately 40% of the transmit
frequency deviation (see the AFC section).
Data Synchronizer
An oversampled digital PLL is used to resynchronize the
received bit stream to a local clock. The oversampled clock rate
of the PLL (CDR_CLK) must be set at 32 times the data rate.
See the Register 3—Receiver Clock Register Comments section
for a definition of how to program. The clock recovery PLL can
accommodate frequency errors of up to ±2%.
FSK Correlator Register Settings
To enable the FSK correlator/demodulator, Bits R4_DB[5:4] should
be set to 01. To achieve best performance, the bandwidth of the
FSK correlator must be optimized for the specific deviation
frequency that is used by the FSK transmitter.
The discriminator BW is controlled in Register 6 by
Bit R6_DB[4:13] and is defined as
3
10
800
_
_
K
CLK
DEMOD
BW
tor
Discrimina
where:
DEMOD_CLK
is as defined in the Register 3—Receiver Clock
Register section, second comment.
K
= Round(200 × 103/FSK Deviation)
To optimize the coefficients of the FSK correlator, two addi-
tional bits, R6_DB14 and R6_DB29, must be assigned. The
value of these bits depends on whether K (as defined above) is
odd or even. These bits are assigned according to Table 7 and
Table 8.
Table 7. When K Is Even
K
K/2
R6_DB14
R6_DB29
Even
Even
0
0
Even
Odd
0
1
Table 8. When K Is Odd
K
(K + 1)/2
R6_DB14
R6_DB29
Odd
Even
1
0
Odd
Odd
1
1
Postdemodulator Bandwidth Register Settings
The 3 dB bandwidth of the postdemodulator filter is controlled
by Bits R4_DB[6:15] and is given by
Postdemod_BW_Setting
CLK
DEMOD
f
CUTOFF
_
π
2
2
10
where fCUTOFF is the target 3 dB bandwidth in Hz of the post-
demodulator filter. This should typically be set to 0.75 times the
data rate (DR).
Some sample settings for the FSK correlator/demodulator are
DEMOD_CLK = 5 MHz
DR = 9.6 kbps
fDEV = 20 kHz
Therefore,
fCUTOFF = 0.75 × 9.6 × 103 Hz
Postdemod_BW_Setting = 211 π 7.2 × 103 Hz/(5 MHz)
Postdemod_BW_Setting = Round(9.26) = 9
and
K = Round(200 kHz)/20 kHz) = 10
Discriminator_BW = (5 MHz × 10)/(800 × 103) = 62.5 = 63
(rounded to the nearest integer)



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com