| Electronic Components Datasheet Search |
|
VSC8541XMV-05 Datasheet(PDF) 34 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
VSC8541XMV-05 Datasheet(HTML) 34 Page - Microchip Technology |
|
34 / 101 page ![]() Functional Descriptions VMDS-10513 VSC8541-02 Datasheet Revision 4.1 25 multiplexed onto the higher order GMII signals and are only available when using the RGMII or RMII interface modes. To enable this functionality, set register bit 20E2.12 to 1. Figure 18 • SOF Indication 3.16 Forced Speed Mode Link-Up Timing The following table specifies the time the device will take to establish a link when operating in a forced speed mode. When using the 1000 Mbps forced speed mode (register 0 bit 6=1, bit 13=0), manually configure the PHY as master or slave by programming bits 12 and 11 in register 9 (1000BASE-T Control) and MDI or MDIX by programming bits 3:2 in register 19E1 (Extended Mode Control). HP Auto-MDIX is not supported in Forced 1000 Mode. In 100Base-TX mode, HP Auto-MDIX can be disabled by setting register 18 bit 7. Link-up times are given for previously-configured PHYs on each side of the link— that is, the times do not include configuration time prior to attempting link-up. Both the device and link partner must be configured in forced speed mode to achieve the listed link-up times. 3.17 Testing Features The VSC8541-02 device includes several testing features designed to facilitate performing system-level debugging and in-system production testing. This section describes the available features. 3.17.1 Ethernet Packet Generator The Ethernet Packet Generator (EPG) can be used at each of the 10/100/1000BASE-T speed settings for copper Cat5 media to isolate problems between the MAC and the VSC8541-02 device, or between a locally connected PHY and its remote link partner. Enabling the EPG feature disables all MAC interface transmit pins and selects the EPG as the source for all data transmitted onto the twisted pair interface. Note: The EPG is intended for use with laboratory or in-system testing equipment only. Do not use the EPG testing feature when the VSC8541-02 device is connected to a live network. To enable the EPG feature, set the device register bit 29E1.15 to 1. Table 17 • SOF Indication Pin Signal RXD7 RX_SOF RXD6 RX_SOF_CLK RXD5 TX_SOF RXD4 TX_SOF_CLK Table 18 • Forced Speed Mode Link-Up Timing Forced Mode Minimum Maximum Units 1000Base-T Master, HP Auto-MDIX Disabled 292 1600 ms 1000Base-T Slave, HP Auto-MDIX Disabled 220 1400 ms 100Base-TX, HP Auto-MDIX Disabled 43 240 ms 100Base-TX, HP Auto-MDIX Enabled 43 4000 ms CLK DATA SOF 55 55 55 D5 XX |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |