LM5177DCPR datasheet(4/60 Pages) TI2

4 / 60 page

Table 4-1. Pin Functions LM5177 (continued)

Type(1)

Description

Name

No.

EN/UVLO

Enable pin. The pin enables or disables the device. If the pin is less than 0.6 V, the device shuts

down. The pin must be raised above 0.65 V to enable the device. This pin is the enable pin for

the device internal reference circuit and input voltage UVLO comparator input.

Feedback pin for output voltage regulation. Connect a resistor divider network from the output of

the converter to the FB pin.

HB1

Bootstrap supply pin for buck half-bridge. An external capacitor is required between the HB1 pin

and the SW1 pin, respectively, to provide bias to the high-side MOSFET gate driver.

HO1

High-side gate driver output for the buck half-bridge

HO1_LL

Logic level output of the HO1 gate signal. Connect this ground reference PWM signal to an

optional external gate-driver input. If the function is not used, make no external connection to this

pin.

HB2

Bootstrap supply pin for boost half-bridge. An external capacitor is required between the HB2 pin

and the SW2 pin, respectively, to provide bias to the high-side MOSFET gate driver.

HO2

High-side gate driver output for the boost half-bridge

HO2_LL

Logic level output of the HO2 gate signal. Connect this ground reference PWM signal to an

optional external gate-driver input. If the function is not used, make no external connection to this

pin.

IMONOUT

Current monitor output pin. Output of the voltage-controlled current source of the optional current

monitor. Connect the pin to a resistor to sense the voltage across. If the output or input current

sense amplifier is configured as current limiter, an external RC network connected between

IMONOUT and AGND compensates the regulator of the current feedback loop.

Connect the IMONOUT pin to VCC to disable the block and reduce the quiescent current

ISNSN

Negative sense input of the output or input current sense amplifier. An optional current sense

resistor connected between ISNSN and ISNSP can be located either on the input side or on the

output side of the power stage.

In case the current monitor is disabled connect ISNSN to ground

ISNSP

Positive sense input of the output or input current sense amplifier. An optional current sense

resistor connected between ISNSN and ISNSP can be located either on the input side or on the

output side of the power stage.

In case the current monitor is disabled connect ISNSN to ground

LO1

Low-side gate driver output for the buck half-bridge

LO2

Low-side gate driver output for the boost half-bridge

MODE

Digital input to select device operation mode. If the pin is pulled low, power save mode (PSM) is

enabled. If the pin is pulled high, the forced PWM or CCM operation is enabled. The configuration

can be changed dynamically during operation. Do not leave this pin floating.

No internal connection

nFLT

Open-drain output pin for fault indication or power good. This pin is pulled low when FB is outside

a ±10% regulation window around the regulation window of the nominal output voltage.

If the nFLT pin function is not used the pin can be kept floating.

PowerPAD

PAD

Connect the PowerPAD to the analog ground. Use thermal vias to connect to a PCB ground plane

for improved power dissipation.

PGND

Power ground. This pin is the high current ground connection to the low-side gate drivers and for

the internal VCC regulator.

I/O

Switching frequency programming pin. An external resistor is connected to the RT pin and AGND

to set the switching frequency.

SLOPE

A resistor connected between the SLOPE pin and AGND provides the slope compensation ramp

for stable current mode operation in both buck and boost mode.

LM5177

SNVSBU4F – JUNE 2022 – REVISED JANUARY 2025

www.ti.com

Submit Document Feedback

Product Folder Links: LM5177

LM5177DCPR Datasheet(PDF) 4 Page - Texas Instruments

LM5177DCPR Datasheet(HTML) 4 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Datasheet Download

Link URL