ADT7476AARQZ-R datasheet(11/69 Pages) ONSEMI

11 / 69 page

ADT7476A

www.onsemi.com

Figure 20. Reading Data from a Previously Selected Register

SCL

SDA

NO ACK. BY

MASTER

STOP BY

MASTER

START BY

MASTER

FRAME 1

SERIAL BUS ADDRESS BYTE

FRAME 2

DATA BYTE FROM ADT7476A

ACK. BY

ADT7476A

R/W

Write Operations

The SMBus specification defines several protocols for

different types of read and write operations. The ones used

in the ADT7476A are discussed below. The following

abbreviations are used in the diagrams:

• S – START

• P – STOP

• R – READ

• W– WRITE

• A – ACKNOWLEDGE

• A – NO ACKNOWLEDGE

The ADT7476A uses the following SMBus write protocols.

Send Byte

In this operation, the master device sends a single

command byte to a slave device, as follows:

1. The master device asserts a start condition on SDA.

2. The master sends the 7-bit slave address followed

by the write bit (low).

3. The addressed slave device asserts ACK on SDA.

4. The master sends a command code.

5. The slave asserts ACK on SDA.

6. The master asserts a stop condition on SDA, and

the transaction ends.

For the ADT7476A, the send byte protocol is used to write

a register address to RAM for a subsequent single-byte read

from the same address. This operation is illustrated in

Figure 21.

Figure 21. Setting a Register Address for

Subsequent Read

SLAVE

ADDRESS

SA P

ADDRESS

If the master is required to read data from the register

immediately after setting up the address, it can assert a repeat

start condition immediately after the final ACK and carry

out a single byte read without asserting an intermediate stop

condition.

Write Byte

In this operation, the master device sends a command byte

and one data byte to the slave device, as follows:

1. The master device asserts a start condition on SDA.

2. The master sends the 7-bit slave address followed

by the write bit (low).

3. The addressed slave device asserts ACK on SDA.

4. The master sends a command code.

5. The slave asserts ACK on SDA.

6. The master sends a data byte.

7. The slave asserts ACK on SDA.

8. The master asserts a stop condition on SDA,

and the transaction ends.

This operation is illustrated in Figure 22.

Figure 22. Single-byte Write to a Register

SLAVE

ADDRESS WA

DATA

A P

ADDRESS

Read Operations

The ADT7476A uses the following SMBus read

protocols.

Receive Byte

This operation is useful when repeatedly reading a single

operation, the master device receives a single byte from a

slave device, as follows:

1. The master device asserts a start condition on SDA.

2. The master sends the 7-bit slave address followed

by the read bit (high).

3. The addressed slave device asserts ACK on SDA.

4. The master receives a data byte.

5. The master asserts NO ACK on SDA.

6. The master asserts a stop condition on SDA, and

the transaction ends.

In the ADT7476A, the receive byte protocol is used to

read a single byte of data from a register whose address has

previously been set by a send byte or write byte operation.

This operation is illustrated in Figure 23.

Figure 23. Single-byte Read from a Register

SLAVE

ADDRESS

DATA

SA P

ADT7476AARQZ-R Datasheet(PDF) 11 Page - ON Semiconductor

ADT7476AARQZ-R Datasheet(HTML) 11 Page - ON Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69

Datasheet Download

Link URL