| Electronic Components Datasheet Search |
|
HC705P6AGRS/D Datasheet(PDF) 31 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
HC705P6AGRS/D Datasheet(HTML) 31 Page - NXP Semiconductors |
|
31 / 134 page ![]() MC68HC705P6A — Rev. 1.0 General Release Specification Operating Modes General Release Specification — MC68HC705P6A Section 3. Operating Modes 3.1 Contents 3.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 3.3 User Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 3.4 Bootloader Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 3.5 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 3.5.1 STOP Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 3.5.1.1 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 3.5.1.2 Halt Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 3.5.2 WAIT Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 3.6 COP Watchdog Timer Considerations . . . . . . . . . . . . . . . . . . .37 3.2 Introduction The MC68HC705P6A has two modes of operation that affect the pinout and architecture of the MCU: user mode and bootloader mode. The user mode is normally used for the application and the bootloader mode is used for programming the EPROM. The conditions required to enter each mode are shown in Table 3-1. The mode of operation is determined by the voltages on the IRQ/VPP and PD7/TCAP pins on the rising edge of the external RESET pin. The mode of operation is also determined whenever the internal COP watchdog timer resets the MCU. When the COP timer expires, the voltage applied to the IRQ/VPP pin controls the mode of operation while the voltage applied to PD7/TCAP is ignored. The voltage applied to PD7/TCAP during the last rising edge on RESET is stored in a latch and used to determine the mode of operation when the COP watchdog timer resets the MCU. Freescale Semiconductor, Inc. For More Information On This Product, Go to: www.freescale.com |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |