| Electronic Components Datasheet Search |
|
ZSSC3036CC1C Datasheet(PDF) 31 Page - List of Unclassifed Manufacturers |
|
|
|||||||||||||||||||||||||||||
ZSSC3036CC1C Datasheet(HTML) 31 Page - List of Unclassifed Manufacturers |
|
31 / 49 page ![]() ZSSC3036 Low-Power 16-Bit Sensor Signal Conditioner IC Data Sheet May 28, 2013 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 1.20 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. 31 of 49 S SlaveAddr 1 A Status A MemDat <15:8> A MemDat <7:0> N P S SlaveAddr 1 A Status A BridgeDat <15:8> A BridgeDat <7:0> N P A TempDat <15:8> A TempDat <7:0> Read Data (I 2C™ Read) (a) Example: after the completion of a Memory Read command read (b) Example: after the completion of a Full Measurement command (ACHEX) read Figure 3.10 I 2C™ Read Data All mandatory I²C-bus protocol features are implemented. Optional features like clock stretching, 10-bit slave address, etc., are not supported by the ZSSC3036 ’s interface. In I²C-High-Speed Mode, a command consists of a fixed length of three bytes. 3.6. Memory In the ZSSC3036, the memory is organized page-wise and can be programmed multiple (4) times (MTP). Each register can only be programmed once per page. The valid page is determined by the page counter which can be incremented with the command 5EHEX – this leads to a “reset” of all registers and a re-programming is necessary. Increasing the customer page counter will disable all old register contents of the former page. It is possible to (re-)program a total of 4 pages. Resetting the page counter is not possible. The page counter starts with 0 and can be incremented to a maximum of 3. If the 4 th memory page has been used, no further changes in the memory are possible – careful writing and page incrementing is strongly recommended. There are two MTP page types: Customer Page: accessible by means of regular write operations (40 HEX to 57HEX). It contains: the customer ID, interface setup data, measurement setup information, calibration coefficients, etc. ZMDI Page: only accessible for write operations by ZMDI. The ZMDI page contains specific trim information and is programmed during manufacturing test by ZMDI. 3.6.1. Programming Memory Programming memory requires a specific supply voltage level (>2.9V) at the VDD pin (see section 1.3 for specifications). The MTP programming voltage itself is generated by means of an implemented charge pump, generating an internal memory programming voltage (VPP); no additional, external voltage, other than VDD needed. The program timing is shown in Figure 3.11. Supplying the ZSSC3036 with VDD>2.9V during memory programming is required. After the memory is programmed, it must be read again to verify the validity of the memory contents. |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |