Electronic Components Datasheet Search
  New Zealand  ▼
ALLDATASHEET.CO.NZ

X  

TMP320F2810PBKA Datasheet(PDF) 29 Page - Texas Instruments

Part # TMP320F2810PBKA
Description  DIGITAL SIGNAL PROCESSORS
PDF  103 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  TI [Texas Instruments]
Direct Link  http://www.ti.com
Logo TI - Texas Instruments

TMP320F2810PBKA Datasheet(HTML) 29 Page - Texas Instruments

Back Button TMP320F2810PBKA Datasheet HTML 25Page - Texas Instruments TMP320F2810PBKA Datasheet HTML 26Page - Texas Instruments TMP320F2810PBKA Datasheet HTML 27Page - Texas Instruments TMP320F2810PBKA Datasheet HTML 28Page - Texas Instruments TMP320F2810PBKA Datasheet HTML 29Page - Texas Instruments TMP320F2810PBKA Datasheet HTML 30Page - Texas Instruments TMP320F2810PBKA Datasheet HTML 31Page - Texas Instruments TMP320F2810PBKA Datasheet HTML 32Page - Texas Instruments TMP320F2810PBKA Datasheet HTML 33Page - Texas Instruments Next Button
Zoom Inzoom in Zoom Outzoom out
 29 / 103 page
background image
TMS320F2810, TMS320F2812
DIGITAL SIGNAL PROCESSORS
SPRS174B – APRIL 2001 – REVISED SEPTEMBER 2001
29
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251–1443
timing registers (continued)
The individual timing parameters can be programmed into the XTIMING registers as described in Table 14.
Table 14. XTIMING0/1/2/6/7 Register Bit Definitions
BIT
NAME
ACCESS
RESET
DESCRIPTION
1:0
XWRTRAIL
R/W
1,1
Two-bit field that defines the write cycle trail period, in XTIMCLK cycles, from
0,1,2,3 (if X2TIMING bit is 0) or 0,2,4,6 (if X2TIMING bit is 1).
4:2
XWRACTIVE
R/W
1,1,1
Three-bit field that defines the write cycle active wait-state period, in XTIMCLK
cycles, from 0,1,2,3,4,5,6,7 (if X2TIMING bit is 0) or 0,2,4,6,8,10,12,14 (if
X2TIMING bit is 1).
Notes: 1. If the USEREADY bit is set to 1 (using XREADY),
then XWRACTIVE must be
≥ 1.
2. The active period is by default 1 cycle. Hence the total active period
is 1 + XWRACTIVE value.
6:5
XWRLEAD
R/W
1,1
Two-bit field that defines the write cycle lead period, in XTIMCLK cycles, from 1,2,3
(if X2TIMING bit is 0) or 2,4,6 (if X2TIMING bit is 1).
Note:
XWRLEAD must be
≥ 1.
8:7
XRDTRAIL
R/W
1,1
Two-bit field that defines the read cycle trail period, in XTIMCLK cycles, from
0,1,2,3 (if X2TIMING bit is 0) or 0,2,4,6 (if X2TIMING bit is 1).
11:9
XRDACTIVE
R/W
1,1,1
Three-bit field that defines the read cycle active wait-state period, in XTIMCLK
cycles, from 0,1,2,3,4,5,6,7 (if X2TIMING bit is 0) or 0,2,4,6,8,10,12,14
(if X2TIMING bit is 1).
Notes: 1. If the USEREADY bit is set to 1 (using XREADY),
then XRDACTIVE must be
≥ 1.
2. The active period is by default 1 cycle. Hence the total active period
is 1 + XRDACTIVE value.
13:12
XRDLEAD
R/W
1,1
Two-bit field that defines the read cycle lead period, in XTIMCLK cycles, from 1,2,3
(if X2TIMING bit is 0) or 2,4,6 (if X2TIMING bit is 1).
Note:
XRDLEAD must be
≥ 1.
14
USEREADY
R/W
1
When set, the XREADY signal can be used to further extend the active portion of
the cycle past the minimum defined by the XRDACTIVE and XWRACTIVE fields.
When cleared XREADY is ignored.
15
READYMODE
R/W
1
When set, the XREADY input is asynchronous. When cleared, the XREADY input
is synchronous.
17:16
Reserved
R/W
1,1
Reserved.
These two bits must always be written to as 1,1. Any other combination is reserved
and will result in incorrect XINTF behavior.
21:18
Reserved
R
0
Reserved
22
X2TIMING
R/W
1
This bit specifies the scaling factor of the LEAD, ACTIVE, TRAIL values in the
individual timing registers. If this bit is 0, the values are scaled 1:1. If this bit is 1,
the values are scaled 2:1 (doubled). The default mode of operation on power up
and reset is 2:1 scaling (doubled) mode.
31:23
Reserved
R
0



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100  ...More


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com