TMS320F241FN datasheet(15/66 Pages) TI

15 / 66 page

TMS320C242

DSP CONTROLLER

SPRS063B – DECEMBER 1997 – REVISED DECEMBER 1999

POST OFFICE BOX 1443

• HOUSTON, TEXAS 77251–1443

digital I/O control registers

Table 4 lists the registers available in the digital I/O module. As with other ’C242 peripherals, the registers are

memory-mapped to the data space.

Table 4. Addresses of Digital I/O Control Registers

ADDRESS

NAME

7090h

OCRA

I/O mux control register A

7092h

OCRB

I/O mux control register B

7098h

PADATDIR

I/O port A data and direction register

709Ah

PBDATDIR

I/O port B data and direction register

709Ch

PCDATDIR

I/O port C data and direction register

709Eh

PDDATDIR

I/O port D data and direction register

device reset and interrupts

The TMS320x24x software-programmable interrupt structure supports flexible on-chip and external interrupt

configurations to meet real-time interrupt-driven application requirements. The ’C242 recognizes three types of

interrupt sources:

D Reset (hardware- or software-initiated) is unarbitrated by the CPU and takes immediate priority over any

other executing functions. All maskable interrupts are disabled until the reset service routine enables them.

The ’C242 device has two sources of reset: an external reset pin and a watchdog timer timeout (reset).

D Hardware-generated interrupts are requested by external pins or by on-chip peripherals. There are two

types:

–

External interrupts are generated by one of four external pins corresponding to the interrupts XINT1,

XINT2, PDPINT, and NMI. The first three can be masked both by dedicated enable bits and by the CPU’s

interrupt mask register (IMR), which can mask each maskable interrupt line at the DSP core. NMI, which

is not maskable, takes priority over peripheral interrupts and software-generated interrupts. It can be

locked out only by an already executing NMI or a reset.

–

Peripheral interrupts are initiated internally by these on-chip peripheral modules: the event manager,

SCI, WD, and ADC. They can be masked both by enable bits for each event in each peripheral and by the

CPU’s IMR, which can mask each maskable interrupt line at the DSP core.

D Software-generated interrupts for the ’C242 include:

–

The INTR instruction. This instruction allows initialization of any ’C242 interrupt with software. Its

operand indicates the interrupt vector location to which the CPU branches. This instruction globally

disables maskable interrupts (sets the INTM bit to 1).

–

The NMI instruction. This instruction forces a branch to interrupt vector location 24h, the same location

used for the nonmaskable hardware interrupt NMI. NMI can be initiated by driving the NMI pin low or by

executing an NMI instruction. This instruction globally disables maskable interrupts.

–

The TRAP instruction. This instruction forces the CPU to branch to interrupt vector location 22h. The

TRAP instruction does

not disable maskable interrupts (INTM is not set to 1); therefore, when the CPU

branches to the interrupt service routine, that routine can be interrupted by the maskable hardware

interrupts.

–

An emulator trap. This interrupt can be generated with either an INTR instruction or a TRAP instruction.

TMS320F241FN Datasheet(PDF) 15 Page - Texas Instruments

TMS320F241FN Datasheet(HTML) 15 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66

Datasheet Download

Link URL