ATmega64A datasheet(57/392 Pages) ATMEL

57 / 392 page

8160C–AVR–07/09

ATmega64A

10.3.3

Safety Level 2

In this mode, the Watchdog Timer is always enabled, and the WDE bit will always read as one. A

timed sequence is needed when changing the Watchdog Time-out period. To change the

Watchdog Time-out, the following procedure must be followed:

In the same operation, write a logical one to WDCE and WDE. Even though the WDE

always is set, the WDE must be written to one to start the timed sequence.

Within the next four clock cycles, in the same operation, write the WDP bits as desired,

but with the WDCE bit cleared. The value written to the WDE bit is irrelevant.

10.4

10.4.1

MCUCSR – MCU Control and Status Register

(1)

The MCU Control and Status Register provides information on which reset source caused an

MCU Reset.

Note:

1. Only EXTRF and PORF are available in mega103 compatibility mode.

• Bit 4 – JTRF: JTAG Reset Flag

This bit is set if a reset is being caused by a logic one in the JTAG Reset Register selected by

the JTAG instruction AVR_RESET. This bit is reset by a Brown-out Reset, or by writing a logic

zero to the flag.

• Bit 3 – WDRF: Watchdog Reset Flag

This bit is set if a Watchdog Reset occurs. The bit is reset by a Power-on Reset, or by writing a

logic zero to the flag.

• Bit 2 – BORF: Brown-out Reset Flag

This bit is set if a Brown-out Reset occurs. The bit is reset by a Power-on Reset, or by writing a

logic zero to the flag.

• Bit 1 – EXTRF: External Reset Flag

This bit is set if an External Reset occurs. The bit is reset by a Power-on Reset, or by writing a

logic zero to the flag.

• Bit 0 – PORF: Power-on Reset Flag

This bit is set if a Power-on Reset occurs. The bit is reset only by writing a logic zero to the flag.

To make use of the reset flags to identify a reset condition, the user should read and then reset

the MCUCSR as early as possible in the program. If the register is cleared before another reset

occurs, the source of the reset can be found by examining the Reset Flags.

10.4.2

WDTCR – Watchdog Timer Control Register

Bit

76543210

0x34 (0x54)

JTD

–

JTRF

WDRF

BORF

EXTRF

PORF

MCUCSR

Read/Write

R/W

Initial Value

See Bit Description

Bit

7654

3210

0x21 (0x41)

–

WDCE

WDE

WDP2

WDP1

WDP0

WDTCR

Read/Write

R/W

Initial Value

0000

ATmega64A Datasheet(PDF) 57 Page - ATMEL Corporation

ATmega64A Datasheet(HTML) 57 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL