UJA1075TWSLASH5V0SLASHWD datasheet(38/53 Pages) NXP

38 / 53 page

UJA1075_2

All information provided in this document is subject to legal disclaimers.

Product data sheet

Rev. 02 — 27 May 2010

38 of 53

NXP Semiconductors

UJA1075

High-speed CAN/LIN core system basis chip

Vth(RX)dif

differential receiver

threshold voltage

CAN Active mode

VV2 = 4.5 V to 5.5 V

−30 V < V

CANH < +30 V

−30 V < V

CANL < +30 V

0.5

0.7

0.9

CAN Lowpower mode

−12 V < V

CANH < +12 V

−12 V < V

CANL < +12 V

0.4

0.7

1.15

Vhys(RX)dif

differential receiver

hysteresis voltage

CAN Active mode

VV2 = 4.5 V to 5.5 V

−30 V < V

CANH < +30 V

−30 V < V

CANL < +30 V

120

400

Ri(cm)

common-mode input

resistance

CAN Active mode; VV2 = 5 V

VCANH = VCANL = 5 V

915

ΔR

input resistance deviation

CAN Active mode; VV2 = 5 V

VCANH = VCANL =5V

−1-

Ri(dif)

differential input resistance

CAN Active mode; VV2 = 5.5 V

VCANH = VCANL = −35 V to +35 V

Ci(cm)

common-mode input

capacitance

CAN Active mode; not tested

Ci(dif)

differential input capacitance CAN Active mode; not tested

ILI

input leakage current

VBAT = 0 V; VV2 = 0 V

VCANH = VCANL =5V

−5

μA

CAN bus common mode stabilization output; pin SPLIT

output voltage

CAN Active mode

VV2 = 4.5 V to 5.5 V

ISPLIT = −500 μA to 500 μA

0.3VV2 0.5VV2 0.7VV2

CAN Active mode

VV2 = 4.5 V to 5.5 V; RL ≥ 1MΩ

0.45

VV2

0.5

VV2

0.55

VV2

leakage current

CAN Lowpower/Off mode or Active

mode with VV2 < 4.5 V

VSPLIT = −30 V to + 30 V

−5-

μA

LIN transmit data input; pin TXDL

Vth(sw)

switching threshold voltage

VV1 = 2.97 V to 5.5 V

0.3VV1 -0.7VV1

Vhys(i)

input hysteresis voltage

VV1 = 2.97 V to 5.5 V

100

900

Rpu

pull-up resistance

LIN receive data output; pin RXDL

IOH

HIGH-level output current

LIN Active mode

VRXDL = VV1 − 0.4 V

−20

−1.5

IOL

LOW-level output current

VRXDL= 0.4 V

1.6

Rpu

pull-up resistance

MC = 00; Standby mode

LIN bus line; pin LIN

IBUS_LIM

current limitation for driver

dominant state

LIN Active mode

VBAT = VLIN = 18 V

VTXDL = 0 V

100

Table 10.

Static characteristics …continued

Tvj = −40 °C to +150 °C; VBAT =4.5 V to 28 V; VBAT > VV1; VBAT > VV2; RLIN = 500 Ω; R(CANH-CANL) = 45 Ω to 65 Ω; all voltages

are defined with respect to ground; positive currents flow in the IC; typical values are given at VBAT = 14 V; unless otherwise

specified.

Symbol

Parameter

Conditions

Min

Typ

Max

Unit

UJA1075TW/5V0/WD Datasheet(PDF) 38 Page - NXP Semiconductors

UJA1075TW/5V0/WD Datasheet(HTML) 38 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53

Datasheet Download

Link URL