| Electronic Components Datasheet Search |
|
PAC1941T-1E/4MX. Datasheet(PDF) 80 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
PAC1941T-1E/4MX. Datasheet(HTML) 80 Page - Microchip Technology |
|
80 / 96 page ![]() PAC194X DS20006543A-page 80 2021 Microchip Technology Inc. REGISTER 7-36: ACCUM CONFIG LAT (4BH) REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ACC1_CONFIG[1:0] ACC2_CONFIG[1:0] ACC3_CONFIG[1:0] ACC4_CONFIG[1:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown This register contains an image of Register 7-19. The bits in this register reflect the value of these settings that were active before the most recent REFRESH command (including REFRESH_V and/of REFRESH_G). The values in register 25h may be programmed but not activated by one of the REFRESH commands and the values in register 4Ah are currently active. This register allows software to determine the actual setting that was active prior to the most recent REFRESH command and, therefore, corresponds to the dataset that is held in the readable registers. This register is valid when the results registers are valid, 1 ms after a REFRESH/_V/_G command. bit 7-6 ACC1_CONFIG[1:0]: Configure the accumulator for Channel 1 to accumulate VPOWER (default), VSENSE or VBUS. 00 = Channel 1 Accumulator accumulates VPOWER 01 = Channel 1 Accumulator accumulates VSENSE 10 = Channel 1 Accumulator accumulates VBUS 11 = Reserved, read as ‘0’. bit 5-4 ACC2_CONFIG[1:0]: Configure the accumulator for Channel 2 to accumulate VPOWER (default), VSENSE or VBUS. 00 = Channel 2 Accumulator accumulates VPOWER 01 = Channel 2 Accumulator accumulates VSENSE 10 = Channel 2 Accumulator accumulates VBUS 11 = Reserved, read as ‘0’. bit 3-2 ACC3_CONFIG[1:0]: Configure the accumulator for Channel 3 to accumulate VPOWER (default), VSENSE or VBUS. 00 = Channel 3 Accumulator accumulates VPOWER 01 = Channel 3 Accumulator accumulates VSENSE 10 = Channel 3 Accumulator accumulates VBUS 11 = Reserved, read as ‘0’. bit 1-0 ACC4_CONFIG[1:0]: Configure the accumulator for Channel 4 to accumulate VPOWER (default), VSENSE or VBUS. 00 = Channel 4 Accumulator accumulates VPOWER 01 = Channel 4 Accumulator accumulates VSENSE 10 = Channel 4 Accumulator accumulates VBUS 11 = Reserved, read as ‘0’. |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |