Electronic Components Datasheet Search
  New Zealand  ▼
ALLDATASHEET.CO.NZ

X  

L99DZ100GP Datasheet(PDF) 124 Page - STMicroelectronics

Part # L99DZ100GP
Description  Automotive door module with LIN and HS-CAN (L99DZ100G) or HS-CAN supporting selective wake up (L99DZ100GP)
PDF  197 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  STMICROELECTRONICS [STMicroelectronics]
Direct Link  http://www.st.com
Logo STMICROELECTRONICS - STMicroelectronics

L99DZ100GP Datasheet(HTML) 124 Page - STMicroelectronics

Back Button L99DZ100GP Datasheet HTML 120Page - STMicroelectronics L99DZ100GP Datasheet HTML 121Page - STMicroelectronics L99DZ100GP Datasheet HTML 122Page - STMicroelectronics L99DZ100GP Datasheet HTML 123Page - STMicroelectronics L99DZ100GP Datasheet HTML 124Page - STMicroelectronics L99DZ100GP Datasheet HTML 125Page - STMicroelectronics L99DZ100GP Datasheet HTML 126Page - STMicroelectronics L99DZ100GP Datasheet HTML 127Page - STMicroelectronics L99DZ100GP Datasheet HTML 128Page - STMicroelectronics Next Button
Zoom Inzoom in Zoom Outzoom out
 124 / 197 page
background image
Serial Peripheral Interface (SPI)
L99DZ100G, L99DZ100GP
124/197
DS11546 Rev 5
A Read & Clear Operation will lead to a clear of addressed status bits. The bits to be cleared
are defined first by address, second by payload bits set to ‘1’. Beside this a shift out of the
content (data present at Communication Start) of the registers is performed.
Note:
Status registers which change status during communication could be cleared by the actual
Read & Clear Operation and are neither reported in actual communication nor in the
following communications. To avoid a loss of any reported status it is recommended just
clear status registers which are already reported in the previous communication (Selective
Bitwise Clear).
Advanced operation codes
To provide beside the separate write of all control registers and the bitwise clear of all status
registers, two Advanced Operation Codes can be used to set all control registers to the
default value and to clear all status registers. A ‘set all control registers to default’ command
is performed when an OpCode ‘11’ at address b’111111 is performed.
Note:
Please consider that potential device specific write protected registers cannot be cleared
with this command as therefore a device Power-on-Reset is needed.
A ‘clear all status registers’ command is performed when an OpCode ‘10’ at address
b’111111 is performed.
Data-in payload
The Payload (Data Byte 1 to Data Byte 3) is the data transferred to the devices with every
SPI communication. The Payload always follows the OpCode and the Address bits. For
Write access the Payload represents the new data written to the addressed register. For
Read & Clear operations the Payload defines which bits of the adressed Status Register will
be cleared. In case of a ‘1’ at the corresponding bit position the bit will be cleared.
For a Read Operation the Payload is not used. For functional safety reasons it is
recommended to set unused Payload to ‘0’.
SDO frame
The data-out frame consists of 32-bit (GSB + Data Byte 1 to 3).
The first eight transmitted bits contain device related status information and are latched into
the shift register at the time of the Communication Start. These 8-bit are transmitted at every
SPI transaction. The subsequent bytes contain the payload data and are latched into the
shift register with the eighth positive SCK edge. This could lead to an inconsistency of data
between the GSB and Payload due to different shift register load times. Anyhow, no
unwanted Status Register clear should appear, as status information should just be cleared
with a dedicated bit clear after.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100  ...More


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com