MPF7100BVMA2ES datasheet(45/125 Pages) NXP

45 / 125 page

NXP Semiconductors

PF7100

7-channel power management integrated circuit for high performance applications

PF7100

All information provided in this document is subject to legal disclaimers.

Product data sheet

Rev. 4 — 9 March 2021

45 / 125

A high to low transition on the XINTB pin sets the XINTB_I interrupt bit and causes the

INTB to be asserted, provided the interrupt is not masked.

The XINTB_S bit follows the actual status of the XINTB pin even when the XINTB_I has

been cleared or the interrupt has been masked.

This pin is internally pulled up to VDDIO with a 1.0 MΩ resistor; therefore, it can be left

unconnected when the XINTB is not used.

14.9.6 WDI

WDI is an input pin to the PF7100 and is intended to operate as an external watchdog

monitor.

When the WDI pin is connected to the watchdog output of the processor, this pin is used

to detect a pulse to indicate that a watchdog event is requested by the processor. When

the WDI pin is asserted, the device starts a watchdog event to place the PMIC outputs in

a default known state.

The WDI pin is monitored during the system-on states. In the OFF modes and during the

power up sequence, the WDI pin is masked until RESETBMCU is de-asserted.

The WDI can be configured to assert on the rising or the falling edge using the

OTP_WDI_INV bit.

• When OTP_WDI_INV = 0, the device starts a WD event on the falling edge of the WDI.

• When OTP_WDI_INV = 1, the device starts a WD event on the rising edge of the WDI.

A 10 µs debounce filter is implemented on either rising or falling edge detection to

prevent false WDI signals to start a watchdog event.

The OTP_WDI_MODE bit allows the WDI pin to react in two different ways:

• When OTP_WDI_MODE = 1, a WDI asserted performs a hard WD reset.

• When OTP_WDI_MODE = 0, a WDI asserted performs a soft WD reset.

The WDI_STBY_ACTIVE bit allows the WDI pin to generate a watchdog event during the

standby state.

• When WDI_STBY_ACTIVE = 0, asserting the WDI does not generate a watchdog

event during the standby state.

• When WDI_STBY_ACTIVE = 1, asserting the WDI starts a watchdog event during the

standby state.

The OTP_WDI_STBY_ACTIVE is used to configure whether the WDI is active in the

standby state or not by default upon power up.

See Section 15.10 "Watchdog event management" for details on watchdog event.

14.9.7 EWARN

EWARN is an active high output, used to notify that an imminent power failure is about to

occur. It should be pulled down to GND by a 100 kΩ resistor.

When a power down is initiated due to a fault, the EWARN pin is asserted before the

device starts powering down as defined by the EWARN_TIME[1:0] bits in order to allow

the system to prepare for the imminent shutdown.

The following faults cause the EWARN pin to be asserted:

• Fault timer expired

MPF7100BVMA2ES Datasheet(PDF) 45 Page - NXP Semiconductors

MPF7100BVMA2ES Datasheet(HTML) 45 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL